Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi there,
as already mentioned in other tickets I'm developing a usb to uart bridge based on the nrf52820. The nRF5 SDK version I'm using is 17.1.0.
Right now I'm facing...
Hi,
When nrf9160 as serial modem, can AT command be sent/received over SPI interface without modify FW ?
As I know, the UART interface is the default setting for transmission...
Hi,
I'm trying to connect multiple device on the same peripheral (nrf5340), but my peripheral does not restart advertising once a device is connected.
How to reproduce...
Now we don't add the external capacitance and want to change the internal capacitance . I have install the test tool and send the command to write the register,but it seems...
Hi!
I have nRF5340 Devkits and already have my own PCBs with nRF5340 chips onboard. I have a task where I need to evaluate how good will be BLE signal in different locations...
I know that I can memory-map external flash using XIP in the NRF52 and NRF53. However, with XIP, you can't write to the memory-mapped addresses (makes sense since you don...
Hi,
I have written a code for the motor driver and that is going to be flashed onto nRF5340. There are two communication buses that I am using in the code: UART and GPIO...
Hello Nordic,
we want to use the nrf9160 to measure some stuff and send data to a server while being battery powered. Therefore we need the lowest power consumption possible...
hi is there any existing frameworks for the nrf52 avoiding zephyr. (eg using common native cmsis / freertos / lwip stacks)?
ideally looking for free (non keil) based SD...
Hi,
Whenever I try to run the NUS example at 115200 baudrate there is an error. Either it triggers an assert or I receive corrupted data.
What should be the ideal baud...
Hi,
Trying to understand the NFC example code in the nRF52 SDK. Just wondering why the source code is not provided for the NFC. Why is this developned in the form of static...
I'm looking into the power consumption of our code, and have reached the point where it looks like our application isn't going into sleep mode properly, and is using several...
I'm developing battery powered Zigbee End Device on SDK 4.2.0. I need to be able to receive commands from Zigbee Coordinator so I'm using SYSTEM ON sleep mode.
Right now...
Hi,
I'm using nRF9160 SLM application SDK 1.9.1
We are using the GPS in 4 operation modes and in between we sent nRF to sleep, it seems when we sent it to sleep all...
