i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Hello,
I'm build my application using v1.9.1 and Visual Code. It seems I have an error saying my application size is greater than the flash size.
I CANNOT jettison any...
I have a big issue about WDT during FDA 510K preparing. I have to proof that WDT of nRF52832 is seperated structurally from main system. since nRF52832 have such a seperated...
To whom it may concern,
I have a project (using Zephyr) where I need to switch UART pins while runtime. Is there a way I can handle this? This is how I initialize pinctrl...
I am using the light_bulb sample from NCS v2.0.0 with an nRF52840 DK board. I changed prj.conf to enable Warning traces from ZBOSS:
+# Enable traces on UART_1 (P1.02) @...
Hello,
I have a question regarding the advertising and scaning mechanism implemented in Zephyr.
To be more precise, suppose the node's radio is in scan mode, and it's...
We want to create solution/project for family of boards using segger embedded studio. We want to create the solution/project in such a manner that new boards software can...
Hello,
I want to build in a reset function for handling certain error states on the 9160DK running nRF Conenct 1.6.0. In the datasheet it appears that nRESET is p0.32 and...
Hi,
I am looking for a way to count the pulses going out of a GPIO pin. If I configure that pin with the input buffer connected, how can I route that signal to a timer/counter...
Hello ,
I am a firmware engineer in Taiwan ,
I already use nRF52820 to finish one case ( cheaper alcohol/acetone BT checker.)
I used USB/ BT wireless uart / Uart send...
Hello,
I have some problems with connecting and interacting with my nRF9160. It doesn't show up in LTE Link Monitor, only got "No supported devices connected" - If i have...
Hello,
nRF52832, SEGGER Embedded Studio for ARM V4.12
We want to improve BLE transmission speed between nRF52832 and iPad mini.
Now condition and transmission speed...
I have two devices:
NRF52832_xxAA_REV2
NRF52840_xxAA_REV3
Running the Zephyr blinky sample application with the following KConfig option added:
CONFIG_NRF_APPROTECT_LOCK...
Hello,
I am trying to create a Matter device by following the steps in https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_matter_creating_accessory.html...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
We are preparing NFC with classic tag.(Not connected to nrf52832, separated custom tag) Recently I found that android cannot...
