But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Thingy:91X V1.0.0 (multiple devices)
NCS 2.6.2, nrf53_connectivity_bridge_v2.0.1
Using the logging of the nRF9151 via the nrf53_connectivity_bridge_v2.0.1 shows on longer...
Hi, We have a network of air quality nodes based on the nrf9160 using Vodacom in South Africa. One morning all the nodes went offline and we discovered that they no longer...
Dear Nordic Technical Support,
I'm writing to report an issue I'm experiencing when trying to integrate MCUboot with a Zigbee R23 project for the nRF54L15 platform.
Issue...
Hi, I am having trouble with the connection of my mesh nodes and my Smartphone over the nRF Mesh App. After flashing my boards ( nRF - 52833, 52840, and 7002), most of the...
Hi,
I adapted the nus_client from the Nordic Connect SDK v2.7.0. I changed the UUID and some function names, but in general the code stays the same. I can subscribe one...
HI all,
I'm trying to run the USB next stack-based loopback class with Linux testusb. and only very few of them been passed and everything else been timed out.
I confirmed...
Dear Support
We currently use a custom PCB board with RAK4630 (NRF52840 + Semtech SX1262)
We started to try with RAK sample located here
https://github.com/RAKWireless...
Hello,
We have nRF52832 in production on a custom board. Recently, we created a new functionality with the aim to handle flash more efficiently, and to avoid the case where...
Hi All,
Hardware Details:
nRF-SDK: 2.8
Microcontroller: nRF52840
Setup:
We have an OpenThread (OT) mesh network consisting of approximately 15 devices. All devices...
Hi,
We are currently developing a solution where a Thingy91 acts as a BLE central. We have had a lot of issues with BLE when using the nRF52 as a HCI device being controlled...
We are making a board with nrf9161 and nrf54L15 so that we have the GPS tracking facility and BLE . We wish to connect (send) other devices' data to this device (like temperature...
We are trying to incorporate nRF9160 to our project. In which we need both GNSS and LTE features. The solution is a tracking device so we need the GPS functionality. We have...
Dear Customer Support,
Wanted to open a case to follow up on this old one Case ID: 335484
I initially looked at the counter alarm under
https://github.com/zephyrproject...
I am looking to figure out my current consumption with an NRF52832 chip. I have the NRF chip running at 3V using UART, SAADC, BLE and SPI. The chip is constantly reading some...
