Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
NCS main
Serial LTE modem does not compile with CONFIG_SLM_START_SLEEP=y in prj.conf
There is missing #include <hal/nrf_reset.h> in main.c but even after including it...
Hello all, I tried installing Segger mebedded studio on a new PC and followed the install steps from the getting started guide. Everything seems to be installed correctly...
Hi there,
we are a student project and are using the nRF51822 Chip with the MDBT40 module. We designed our own custom PCB and followed the instructions for the circuit as...
I have a subroutine that exercises the SPI interface and only at certain points in the code it won't execute the SPI subroutine and goes into the disassembly when single stepping...
SES IDE, nor nrfConnect programmer tool sees the JLink programmer attached to my PC. No "idcode" in SES. No devices appear in Programmer.
Windows10.
JLink_Windows_V764e_x86_64...
Hello,
I am beginner to work with Nordic, I am trying to setup the development environment for nRF5340 Chipset.
For that install nRF Connect Desktop v3.11.0 version. ...
Hi Team
My SES crashed suddenly. When I tick file->nRF Connect SDK Project, It show below error information. I have try to re-install the NCS from toolchain manager. It...
Hi Team,
I have nRF52 DK PCA 10040.
PC: Windows 10 pro
IDE: Keil uVision 5
Working with nRF5 SDK 17.1.0 with S132 soft device .
To execute the code , first i flashed...
Hi,
Zephyr 3.0 , nrf5340 ncs 1.9.1
i can successfully sent data with
this function ;
So it sends 2 transactions without changing cs state.
1byte tx+rx , and...
Hi,Master:
In BT core_v5.0 2.3.5.6.3 Authentication Stage 1 – Passkey Entry, as shown in the figure below
Question: Why does the process loop 20 times, verifying one bit...
Hi,
I have used the nRF Connect Mobile app to connect a BLE device to my Android device. Once bonded, I can receive temperature signals as expected without issue. I can...
Hi,
I am testing MCUboot in nrf52840 DK
I know that MCUboot can image update using slot 0, slot 1, and scratch area
If so, is it possible to update the softdevice(BLE...
Hello,
We are working on NRF52832 + nRF Connect SDK 1.8.0 for our upcoming product. We need to do OTA of our Firmware.
Could you please help with pointing to the right...
Hi Nordic,
We are using NRF52840 and the NCS sdk to design a new product which may have multiple threads designed. And each thread may need to do some BLE operation at the...
