Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hello, I am having a problem with the development on a custon board. During system-off I wake up the chip with nrf_gpio_cfg_sense_input function on PIN 5. The chip wakes up...
Hi
I am designing a new BLE device and have some questions about the PCB antenna.
The product will be worn on the body.
I have a 4 Layer PCB with 1.0mm with and 35u...
Im trying to use the BLE LTE Gateway running on a NRF9160DK
I have the NRF52840 running the lpuart_hci code and that is working fine i can configure the BLE from the NRF9160...
I have nRF9160DK kit. The iBASIS SIM does not work in India. I aaranged a M2M SIM from Voadfone. The Vodafone SIM has 20 digit ICCID printed on it, while the nrfcloud accepts...
SDK version - 15.3
Segger version - 5.42
DK - nRF52840
I'm a beginner and I was following this tutorial our_services . The code given in the tutorial worked for SDK...
Hi
I am testing nRF52833 UART DFU function, but there is an error in merged HEX file,
Parsing input files. Merging file "SD.hex" into output. Merging file "APP.hex"...
When associating a pin with the UART, is it possible to still configure the pin to be open drain and with a pullup, or does the peripheral associating override those sett...
Hi :) ,
I'm using TWI to connect a sensor that i supply with an LDO regulator.
This LDO has an enable pin controlled by P0_23. Driving current is max 1uA so i configured...
In our project, we have defined 5 FDS_VIRTUAL_PAGES each of size 1024 words and have programmed to do GC if > 10 records are deleted. I see the 1st page being used for storing...
i have installed segger ide and nrf connect for desktop for programm nrf9160 , i have successfully uploaded Blinky code (zephyr) .but now i want to create a new project ....
Hi, I am trying the MQTT_SIMPLE sample on both the nRF9160DK and my own custom board. I have mfw_nrf9160_1.3.1 on both nRF9160 and I am using SDK v1.8.0. LTE connection seems...
Hi,
I'm using NCS 1.8.0 on a nrf52840.
I've got what seems to be a corrupted external flash Settings file. The issue doesn't seem reproducible yet, but as it happened...
I am working with SPI for the mfrc522 RFID reader. We were able to read the card previously while we used nRF connect SDK version 1.5.1 and nRF connect 3.6.1
Now I am not...
I'm using modem version mfw_nrf9160_1.3.1
It's waiting for semaphore and when CSCON notification came in between it's just resetting due to some hard fault. Can somebody...
Hi there,
I have gotten to the very last step of the following tutorial: https://www.youtube.com/watch?v=kdMJQFDRoss
The issue I am facing is that when pairing the Matter...
