Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello Nordic Team,
I am trying to flash the existing BLE light example code to my BL653 kit with Segger Embedded Studio. After falshing the code into the board it is taking...
Been having trouble integrating systemview for tracing FreeRTOS application. I came across this thread , and even tried replacing the files with what's inside the PatchedFiles...
Nrf Mesh App Version 3.1.6
After provisioning 2 nodes, I connect to one as a proxy, whenever I try to "get TTL", "Read State", or refresh the configuration server after...
opened nRF connect and attempted to open the dongle with this. When I plug the dongle in without holding the button, i get this error
2021-02-14T20:18:30.648Z INFO Using...
I am unable to generate setting using nrfutil.
Command used is as follow:
nrfutil settings generate --family NRF52840 --application pca10056/blank/armgcc/_build/nrf52840_xxaa...
Hi
I'm trying to use the LIBUARTE library together with BLE_NUS example in SDK 17.2.
From the libuarte sample I add these lines to NUS example:
I also modify sdk_setup...
Hi!
I am trying to flash some Zigbee related code to experiment with creating DIY smart devices (specifically Zigbee and matter ones) using my Arduino nano 33 BLE. One problem...
Hi,
I flashed open_bootloader and it seams to work. I was following this question . However, after building application (I am using ble_central/ble_app_gatts example), creating...
hi,
im using nrf52811 customised board,for long range purpose im using softdevice s140
so i need to port secure boot loader pca10056 to pca10056e
can you please me reagarding...
Hi,
I have tested the ble_nus code in NCS v1.4.2
where i can't send 250 bytes
I want to send 250 bytes to ble nus data send for 100 ms once
How to enable data send...
Hello,
I use the nrf5340 pdk. I would like to flash the led1 with a duty cycle which is different from 50%, so i tried to open the binky_pwm project, but the segger shows...
Hello,
what is the correspondence between the number of pins indicated in the dts file with the port number and bit of the chip.
for instance:
& spi1 {
compatible...
Hi,
I am using nrf5 SDK and working on proprietary Nordic. I saw that in the code there is no option for 250 kbit/s Nordic proprietary for nrf52840. However in nrf52_bitfields...
Hello
I'm using the nrf52dk board. It's been good so far, but suddenly there's a connection problem with Bluetooth.
I tested it with SDK's various ble examples. Debugging...
