i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
nrf_ringbuf has a bug which happens when mixing nrf_ringbuf_cpy_put() with nrf_ringbuf_alloc() and nrf_ringbuf_put(). After copying data with nrf_ringbuf_cpy_put() a later...
Hello,
at the moment we are trying to realize a low power delay with the usage of the APP_TIMER.
We need a low power delay over 10 seconds.
This is our attempt:
...
Hello,
we are developing an application with a nRF52832 on a custom board. The application works fine. The application on the nRF52832 consumes 2.2mA @ 2.5V.
The other...
Hello,
Our Project
at the moment we are developing an application with a BMD-350, which contains a nRF52832 chip.
The BMD-350 is on a custom PCB with another microcontroller...
Hi,
I am trying to prgram the nRF52840 DK board (revision 2.0.1) within a virual machine (VirtualBox running Linux Mint). I have installed the SDK and the nrf command line...
I'm not even exactly sure how to describe this problem, so please bear with me. I have a setup with two nRF52840s, one of them (call it B) functions as a peripheral server...
I have two devices, both nRF52840, one as Client, one as Server. There are a few services defined with a few characteristics in each. Two of the services have values like...
I have now had two units exhibit nearly the exact same behavior, and it seems odd to me for them to be so similar. I'm wondering if anyone else has seen similar. I have a...
Hey all,
I have a USB CDC ACM application that works great when it starts, but I'm not able to get it running without the debugger. This is SDK 17.0.2, there is a SoftDevice...
Hi,
I'm trying to use timers 1, 2 and 3 in my application which also uses the app_timer. It works fine when I'm just use 1 & 2 but after inserting the following code to...
Hi, can you point me to the documentation that tells me what preprocessor defines are required for properly building ble_blinky_c or similar please.
The reason is for setting...
Hello,
I am facing problems when I send 3 consecutive chunks of 244 bytes on BLE. My actual task is like receive from SPI and send it to BLE. I am receiving data in chunk...
Hi,
I need to store the 1kB of data in the flash storage and it need to be read anytime and change the data anywhere.
I am using nrf52840 DK and also nrf5340 DK to perform...
Hi Nordic Leaders,
Regarding nRF5340 and nRF connect SDK
Objective: Update blue tooth data transfer rate between 1Mbps and 2 Mbps.
Details:
As it is not possible to...
