Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Dear Nordic,
I am trying to do the following;
nrf52840dk will be ble central
ios will be peripheral
ios will begin to advertise then nrf52840 will connect
...
We are using SDK 15.0 and Softdevice 6.0, nRF52832
The question is :(1) We migrated the example "ble_app_hrs_freertos" to "ble_app_uart_c",luckily it works ;(2) But when...
HI,
I am using NRF52832,SDK15.2
I need to work on ultra low power consumption because My project related to Health care, Fitness tracker and HOME IOT mesh network.
for...
Hi,
I'm using the TWI master example to test my application. I wanted to extend the example to write into flash (fstorage module), in a way that I can transmit data over...
Hi there, I would like to make pin changes in my program. If my output pin is HIGH I want a function to change it to LOW and if was previously LOW change it to HIGH. Is there...
I am trying to run ble_serial.py in the ble_app_cli SDK example using the nrf52840 dongle. To do so, I tried flashing the connectivity firmware automatically via the nrfConnect...
Hi Group, currently working on nRF52840 chipset based EVK and able to flash program. But I need to port the chipset driver and required files from nRF5_SDK_15.2.0 SDK to my...
Hi,
When i compile the example project( Blinky SysTick Example ) according to the guide, i got this error:
Error instantiating RTE components Error #540: 'NordicSemiconductor...
Hello
Please help me understand how can i connect pin AC13 (P0.18) in dual configuration - QSPI and nRESET.
I would like use a nRF52840 as my main microelectronic. I would...
SoftDevice 132v6.1.0
RKNRFgo (nrfgo studio for Mac OS -- more info here https://devzone.nordicsemi.com/b/blog/posts/tools-for-os-x-development ) used to program SoftDevice...
Hi,
pretty new to my nRF52840 DK,PCA10056. Like to learn more about the BLE but since new to the Blue Tooth programming I need a tutorial
so I can learn step by step....
Dear All,
Thanks for supporting.
I want to include DFU in ble_app_uart example. As per the document i have to successfully compiled DFU bootloader. And also done all settings...
Hi Nordic,
I use NRF51802 SDK 11.0.
Now we encounter the problem of insufficient product code space, so we want to expand the CODE area by modifying the value of DFU_APP_DATA_RESERVED...
Can I wake up the Thingy to do sensor readings by sending a BLE packet to it from another BLE device?
or what are the ways I can get nRF52832/52840 out of deep sleep mode...
Hello
I use nrf52832 SDK14.2 for development, I copy the flash_fstorage example code to my project.
I write the data to flash doesn't have any error, and can read flash...
