Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
My programm uses both the non-secure world and the secure world, with the non-secure-world largely just calling functions inside a custom partition of TFM in the secure world...
Hi,
I'm working with a nRF54L15 within the nRF Connect SDK on Zephyr. I need an array which retains its content through soft resets, so in another RAM section than the...
Greetings,
One question on the nRF9161/51 capabilities: is the 3GPP Rel-14 LTE-M Cat-M1 larger UpLink transport block size (TBS) of 2984 bits supported (instead of 1000...
When debugging a connection using Wireshark and the BLE sniffer, one must select the device of interest from the device menu, or select "follow le address" in the key drop...
I'm checking the nrf_dm sample with NRF52840DK,nrf connect SDK.
Due to peer.c and dm.c create static thread,so I run debug and hope to get all thread and their priority...
Hi,
I am checking the i2c protocol with nRF Connect SDK and Zephyr through VSCode.
I created a very simple example where I push a button on the nRF52840 DK and I get the...
Hi
We are using the NCS V2.6.99 for a sample project which scans for peripheral devices.
I've seen that the scan-callback-function return the struct bt_le_scan_recv_info...
Hi, when I debug my software (nrf5340 cpuapp) from the nRF Connect plugin in VS Code, when I hover over variables and buffers, only the content of the variables is shown,...
We designed a board based on the nRF52840, and are using nrf5 SDK 17.1.0 with S140 SoftDevice. We are using a QSPI flash, MX25U51245G ( https://www.macronix.com/Lists/Datasheet...
product details:
nRF52840 custom board
nRFConnectSDK 2.2.0
we want to implement custom service interacting with the Android app.
Where we will receive on command from...
When creating a Bluetooth Mesh Vendor model ( https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/protocols/bt/bt_mesh/vendor_model/dev_overview.html ) and if the vendor...
Hi there.
I'm using nRF5 SDK 17.1.0 with nrf52840.
I've configured my timer3 to interrupt by compare with 10us ticks. When it does, I toggle a pin. But when I measure...
Hello,
I am developing an app based on the the buttonless_dfu example and the secure bootloader and it works fine with Android.
I have the following problem with IOS:...
Hi all,
I have this annoying issue that I can't find a way to get rid of, and I don't know if it's intentional or if there is even a way to deactivate it.
I'm using VS...
Hi Community,
does someone here have experience with DAPLink?
currently the nRF5340 is still not spported by DAPLink, I`m considering to compile one. here is how to port...