Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
I see other posts stating that the nRF Connect For Desktop 'Toolchain Manager' requires an internet connection to download the nRF Connect SDK versions. I'm thinking of the...
I need to connect a device to an nRF5340 SPI port without creating a custom driver. I'm tempted to use the nrfx_spim driver directly, but I'm trying to do it with Zephyr and...
Hi,
I am migrating from nCS v2.6.1 to v2.9.0, my workspace builds fine on v2.6.1 But on v2.9.0 I am getting the below error:
This is being generated as my main.c has...
Hi
i want to generate security key with the combination of time and private key.can i acheive it in NRF..mainly in NRF52833?
i have a ref code in this repo.. here can...
Hi,
My goal is to primarily save the audio being generated by the Headset device in the LE Audio samples. I have established Bidirectional stream between the Headset and...
I had received a lot of support in: Replacing RS485 link with NRF24L01+ .
At the moment I have 95% proyect working OK but in one operation mode of my program, after some...
it will take about 25uA~ 28uA.
when I remove R18 R19, set io to input with pullup, it will take about 10uA,
&button1 {
gpios = <&gpio0 5 ( GPIO_ACTIVE_LOW | GPIO_PULL_UP...
Hi, I'm having trouble running the samples/net/aws_iot sample on nRF9160-based board.
Configuration: - nCS: v2.6.0 - modem version: nrf9160_1.3.6
When running the sample...
Hi Nordic Team I am working on a BLE application using the nRF5 SDK 17.1.0 with Peer Manager configured for Security Mode 1 Level 4 . I am encountering an issue related to...
Hi,
We found a very strange problem when designing a product using nrf5340: The equipment is coated with a layer of UV tri-proof paint on the chip of nRF5340 and the peripheral...
Hello,
I have an application where I want to read the voltage of a battery every 5 minutes for this I'm using the Zephyr ADC library. But now I also want to read the ADC...
Hello Folks,
I've got a thorny problem that I've spent an entire day minimizing before even trying to post about it here.
Before diving in, however, here are my environment...
Hello,
I want to utilize two units of nRF7002-DK I have, to evaluate LE bluetooth link between the nRF5340 SoCs. I need access to define CIG and CIS between the two SoCs...
Hello,
Im using custom board carring nrf52820,and i want enable UART to contact with another mcu,this is the Schematic.
NCS V2.6.0.I take Peripherial_uart to Peripherial_hid_keyboard...
