Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Dear Nordic, Could you please advise how to interpret the version in this context? The modem firmware v2.X - is it the version that does not exist right now? If yes, when...
Hi everyone,
I'm working on a project where I have four sensors connected to my chip via two SPI buses ( 2 on each with 4 CS). My goal is to read data from these sensors...
I am using an nrf528232 based BLE module, the Taiyo Yuden EYSHSNZWZ: https://www.digikey.com/en/products/detail/kaga-fei-america-inc/EYSHSNZWZ/7104534
Running BLE and uart...
Hello,
I have recently attempted to port over to the latest v2.7.0 of the SDK by following the steps in the latest getting started guide for the L15. I have been able to...
There is this post from three years ago here that mentioned LLPM isn't supported on nRF5340. The answers had mentioned some issues with LLPM on the network core & that the...
NCS v2.6.0, NRF5340dk
I'm trying to configure a project that uses mcuboot with direct XIP with the external QSPI flash. I've been looking at examples in
ncs/v2.6.0/nrf...
Hi! We use Npm1100 SHPACT on GPIO and want to ask connect SHPHLD directly to VBAT.
The spec has 100kOhm resistor between SHPACT and VBAT.
However, we don't use the button...
HI
softdvice : s132
SDK version : nRF5_SDK_17.1.0_ddde560
I am using the nrf_delay_us() function. The product I am using now controls the gpio in us units. Since it...
Hi,
In NCS 2.0, the ability to add a custom child image was added. This works fine but as soon as you include the mcuboot child image, the order of the child image builds...
Hello folks!
Today, I have what I hope is a really easy fix that I just can't find the answer to.
I would like to transition from using the nRF Connect extension "build...
Hi,
First of all I would like to know when the Nordic SDK will be based on Zephyr 3.7.0, which is an LTS version.
Secondly I would like to find an easy way to find out...
looking at https://github.com/nrfconnect/sdk-nrf/tree/main/lib/location
specifically https://github.com/nrfconnect/sdk-nrf/blob/main/lib/location/cloud_service/cloud_service...
Hi, I am working on a project using the nRF52832 and the nRF5 SDK 17.1.0. We have a sensor with non linear behaviour and in our attempt to linearize it we found an article...
