When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi Community I've been trying to read a tag from nRF54L15 board .
When checking the NRF connect SDK NFC examples, It seems the NFC Tag reader example is not supported for...
Hi
I am using NCS 2.8 and running one pair of peripheral and central devices using nRF52832.
At first, the default interval is 50 ms, and I can get the throughput around...
Hi, I'm trying to test Channel Sounding with concurrent measurements using one initiator and two reflectors on nRF54L15 DKs.
From replies in other DevZone threads, it seems...
I currently use NRF5SDK v17 with S112 supporting 0-2 peripherals, ideally using data extension (4.2). No encryption is used and I don't need any 5.0 features. I now wish to...
I plan on using the nPM2100 to power the nRF54L15. I'd like to confirm any recommended practices for using the reset pin of the nPM2100.
nPM2100 PG/RESET to nRF54L15...
Hi, I'm trying to use the nRF COMP peripheral in Zephyr. My application boots and runs normally until I enable the DeviceTree overlay for the COMP. As soon as the overlay...
Hello,
What will happen if I try to change the device's TX power using the vendor-specific command SDC_HCI_OPCODE_CMD_VS_ZEPHYR_WRITE_TX_POWER while LE Power Control feature...
hi,
I use nrf54l15dk with ncs-v3.1.0， the project is based sample "central_hids"；
The purpose is I want to change console uart from "pin1.04/pin1.05<uart20>" to "pin2...
I’m developing a project on the nRF52840 that uses BLE + RTC + an SD card. It’s based on a previous project that only used BLE + RTC, and I’ve added the ability to store data...
I'm trying to use a Power Profiler Kit II with a Mac running Ventura 13.7.8. If I update the Power Profiler App to v4.3.0 or v4.3.1 the PPK II is not detected and this is...
Dear Team,
I am using NRF54L15 DK, where I have UART defined and mapped as following:
uart20_default: uart20_default {
group1 {
psels = <NRF_PSEL(UART_TX, 1 ,...
I'm struggling to obtain stable ADC readings on the nRF54L15, and I'd appreciate any suggestions. I have the ADC configured with gain = 1, internal reference, 10 bit resolution...
Hello,
I'm trying to get a TIMER triggered ADC read on P1.11 AIN4. Sample advanced_non_blocking_internal_timer sounds like what I want but it isn't NRF54L15 compatible...
I am designing a very-low-cost device based on the nRF9151 and would like a quick technical clarification.
My plan is to power the SoC and all GPIO rails from a single 3...
