Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
My device get deep sleep mode. It wakes up from reset button trigger. Because I couldn't gpio pin trigger for wakes up. So I put vibration sensor to reset pin. It wakes up...
Hello, I am developing a custom board based on nRF52832 that should spend most of it's time in SystemOFF mode. Eventually, it will wake up on an GPIO event caused by the external...
Hi,
I've been using the DWT macro cell successfully on the app core to provide high accuracy timing information. E.g., with these declarations:
and enabling the cycle...
hi ~
peripheral can bond how many smartphones ?
and What will happened if over bond?
i use sdk12.2 below 'is my setting
#define SEC_PARAM_BOND 1 #define SEC_PARAM_MITM...
Hi…
I am using freeRTOS V10.0.0 release
I am using nRF52820 + SDK V17.0.2 with SD112 V7.2.0 along with tickless idle as this is a battery based product…
When my application...
Hey guys, I'm an embedded software engineer and I am currently working in a prototype, specifically using the Circuitdojo Feather nRF9160 , I am also using a Hologram International...
Based on the Sample "Bluetooth Peripheral_uart:
My latest attempt to send long data stream:
I send:
1234567890123456789012345678901234567890123456789012345678901234567890...
Hi,
I've met a problem. It seems NVS sometimes erases sector during initialization.
As shown in following log, I wrote 2 datas(address, slot) in NVS. Normally, I can read...
Using the period required for 2Mbps Gazell, 600us, how much does this slow down BLE (bandwidth/# packets)? Also, does the timeslots API work well with nrf52? If I modify this...
Solved, just bad luck, I got 3 broken module, the 4 is ok.
So it module's problem.
======================================================= I am trying to flash "hello...
Hi,
is there any way adjust the ISO channel transmission power (e.g. -20dBm, +2dBm, ...) in the new nRF5340 Audio application? I saw that one can select between 0dBm and...
I have a Thingy91 that I want to connect to nRFcloud. Not knowing the state of its keys/provisioning I followed the procedure to generate just-in-time keys (as a first attempt...
Hello all!
I'm starting development of BLE Mesh network as part of my Master thesis, for which I designed a custom board based on nRF52832 and nRF52840 with some built-in...
I am working on nrf52840 using nrf connect sdk v2.0.0 example periodic_adv, nrf52840 is prodcasting extended advertising, my app is running on Sony Xperia 1 with bluetooth...
