I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
Hello Tech Support Team,
We are looking for a solution that can support LE audio. We currently use CSR8675 to make a Bluetooth dongle.
In order to support LE Audio, we...
Hi,
I'm having some issues trying to install the additional python dependencies for both zephyr and nrf
but it's not really working
I'm using this version of python...
Hi Nordic Team,
We require to perform below BLE range test, for which i would like to know which firmware i can use for the same.
1) To configure one device as continuous...
Hi,
We are testing mass pairing on our windows machines, as we have seen problems with a high number of paired devices.
I am able to increment the mac address by using...
Hi,
A simple CMAKE question, somewhat regarding the zephyr build, but pretty essential for someone using JTAG to debug the application:
How does one disable optimization...
I need to make a reset of mesh device with clearing its configuration.
For this I tried to use model_config_file_clear() or mesh_stack_config_clear() functions.
However...
Hi,
How to enable fast mode for radio transmission and reception (I am using nRF5 SDK). These are the default examples and I can see that fast mode is not implemented: ...
Hello again,
I saw this Github 's post and I was wondering if is possible to use some of the libraries and drivers with nRF52811 and if so should I pay attention to some...
Hi,
Question:
In our project we need to drive some external components (High Side Drivers) via GPIO output.
In order switch on our “High Side Drivers” we need a voltage...
I'm using TWI and BLE functions together. My TWI sensor is operating at 400kHz, low priority. BLE has the highest priority. For example, if nRF52805 is sending commands to...
Hello community, I tried to read my motor encoders with the QDEC and capture the position of my motor. Hardware: nRF52840 DK, 2 Hal motor encoders on pin 0.13 and 0.14 which...
In NCS v1.6.99 the HEX data format is removed from data send and receive commands (socket, udp/tcp cli/srv), only ascii and data mode is supported.
In case of binary data...
Hello,
First time post and brand new to the nRF52832 chip. I am tasked with building firmware that will synchronize ADC samples across multiple devices. I have started with...
Hi to all team,
I have two units of nrf52840 dongle with me.
I have to develop the generic application firmware where data send from one dongle(coordinator) is getting...
