Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi,
My nRF52840 DK has suddenly stopped working. I have tried different USB cables but it's not turning ON when I connect the cable to the J 2 USB connector.
Observation...
Hello
In our application we're using the download client. Here are the cipher suites the modem supports in hardware: https://www.nordicsemi.com/Products/Low-power-cellular...
nRF52840, SD140, SDK 17.0.2
We're using UARTE to communicate with a peer MCU. We're using hardware flow control (CTS and RTS are enabled) and the baudrate is 115200. The...
Hello,
I'm using two nRF5340 MCUs with BLE5.2 audio in an application. I had a couple questions I hoped the Devzone could help answer.
1. On one of the MCUs, I was originally...
sorry for the perhaps stupid question - but despite several hours of intensive searching, I am not getting any further with the start -up of my new and beautiful Thingy91...
I do not understand how to compose these settings.
Using ncs v1.5.0 GPS sample with SUPL enabled.
This works OK on nrf9160-DK using the supplied settings
#define AT_MAGPIO...
Similar to https://devzone.nordicsemi.com/f/nordic-q-a/61935/bootloader-flashing-error---nordic-nrf52840-usb-dongle I get the following error:
DFU failed: Error message...
Hi,
I’m trying to measure the current on NRF52840, SDK 17.0.2.
I have modified the HeartRate Measurement example’s advertising parameters as PLper my requirement.
...
Hi,
I am trying Zephyr for 52840 dongle. I am able to west build, but could not west flash.
While I do west flash, I get
-- west flash: rebuilding ninja: no work...
I bet you get sick of this, but I've looked at the other solutions and followed any advice, but no joy.
I am trying to use a Makerdiary nRF82540-MDK usb dongle to evaluate...
Dears,
When Reset pin(0.18) is used for QSPI (GPIO macro is not defined as RESET), after initialization ,Jlink is disconnect.
Would you please suggest it? Thanks.
I am using a nRF52840 dongle and want to filter ADC raw data. I have downloaded the CMSIS 5 DSP package.
And tried to include a copy of an example (arm_fft_bin_example_f32...
I found that AGPS can get location information via mobile network. With this feature "GPS" can work indoor.
1. Thingy91 also uses AGPS, but when I ran prebuilt hex asset...
Hey all,
I'm trying to install the nRF Asset tracker. I'm stuck at a step called Building the project using GitHub. I just need to know how to build the project using...
Hi,
I was trying to retrieve the log information from the Nordic to the AWS server. I can see all the log info with the Status as Error. I'm retrieving the logs from...
