Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi i am trying to debug the ble Uart app for confuguring device as Central. Which function is responsible for BLE Connection. I unable to debug this code with breakpoints...
I'm using a PCA10040 V1.1.1 dev board (nrf52). I programmed it with "Nordic_HRM" example, but modified it to send 20bytes data at 100Hz.
Then, on my PC, I use a PCA10031...
Hi,
I do not want to use the device id as my unique serial number of the nrf52840 chip and would like to generate my own . Where and how can I store this serial number...
I am using nrf51422 device with the SDK 11. I am running the hear rate application ble_app_hrs_pca10028_s130. When I connect to the device (using the nRF Connect app for ios...
Hi. I send 240 byte long messages using ble_nus_c_string_send at the moment.
How come the length field is a uint16_t if the max size is 247 bytes? Is it for future proofing...
I have a custom design buildt on ble_app_uart peripheral example from SDK 12.2.0. I use a timer that I start from case BLE_ADV_FAST in on_adv_evt to send a message to a display...
Hi,
I am using a PWM to control the output of an LED driver and I am implementing a soft_on function when powering ON the driver, so we have a start_PWM function that looks...
Hi, I want to start some projekt with BT840 module and use Keil to programming it. Also, I have Segger jlink programmer but I don't know how start. Can you give me some tips...
Hello,
we are using nRF52840 and have to directly use the CRYS API of the CryptoCell310.
In the documentation of the function CRYS_HASH_Update, the following is written...
When I use the battery to power on, I get NRF_POWER-> RESETREAS = 0x00010000. I check the register manual to see that it is GPIO wake-up. But I didn't configure GPIO wake...
Hello,
I am using Samsung Galaxy Tab A (2016) with android version 5.1.1 build LMY47V and I can not connect to the bluetooth module at all. In the log of the nrf Connect...
For an ADV_IND advertising event without any Scan Requests, what is the maximum amount of time that the radio's receiver will stay on?
Is this parameter configurable?
...
I am trying to configure SPI with BLE using softdevice S130. But SPI is not working properly when I used it with BLE, although it is working fine without BLE
Hello Nordic,
I am having problems getting the PPK to work with my nrf520840-DK application. I am happy to share my code with you, but first a hardware setup-description...
