But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi
I am going through the ble_app_multirole_lesc example and I can see the following line:-
/* Due to DRGN-7235, dhkey_reply() must come after auth_key_reply() */
...
Hi community,
I'm using the multi-link peripheral example from SDK v6.1.0 with s110 soft device version 7.3.0., this is cross-compiled with arm-none-eabi-gcc.
The both...
Hi all - Im porting projest from Keil4 to Keil5 and am now stuck on this error - division by zero in SDKs sources:
*** Using Compiler 'V5.06 (build 20)', folder: 'C:\Keil_v5...
Hi, I can't seem to find any hardware design guidelines for the nRF52832 chip, I can only find hardware information for the development board.
Best regard Thomas
we add static pass key in example code hrs with dfu，but when connecting with phone，input passkey on phone，the nrf51822 will reboot device_manager_cnfg.h
main.c
Hi Guys,
I'm working with nRF8001 BLE with PIC18F microcontroller, well i have succesfully completed my project but their one last thing i have to add i.e sleep and wakeup...
Hello Nordic,
For my application I need to log external and internal events/state of my device. In order to do so, I need to find a way to keep track on time. I do not...
Issue is similar to
devzone.nordicsemi.com/.../
I'm developing an application based on latest SoftDevice 130_1.0.0 and using two or more DevKits.
My application starts...
Hi. My app based on S130_1.0.0 and is run on DevKit with 51422 chip. App advertises and scans at the same time with next params:
adv interval = 20mS;
scan...
im using nrf51822. before entering DFU mode I want to save data in flash. but when I call pstorage within reset_prepare function, it doesn't jump to DFU mode !!!!
reset_prepare...
Hello guys, i'm new in nRF51 DK board, and i would like to flash the .hex file to my board, but when i do it the board automatically unmounting himself and reset with the...
hello there i want to send negative acknowledgement then what should i do?? like i want to send some data and then i want to send negative acknowledgement
i am trying to use yggdrasil for nrf51422 (pca10028) with sdk 10.0. after installing, i cannot see the com port. How do I flash "connectivity_115k2_with_s130_1.0.0.hex" with...
Hi everyone!. I am beginner for Nordic Devices
I want to use RTC Clock with softdevices
so I loaded the project ble_uart_s130 from examples.
and I changed code like...
