I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi,
After successfully compiling and flashing both the blinky example and the ble_app_hrs on my nRF52840 I ran into an issue with ANT Broadcast TX example. The example...
Hello everyone,
I am working on a project that uses the nRF5340 microcontroller and Zephyr.
Initially I took an EVK-NORA-B106 development board that mounts the NORA-B1...
Hi,
I am using zephyr application. I need your guidance on how to set phy to 125 kbps?
I enabled some configurations regarding this please verify that and let me know...
I can't build the program.
Please help. Thanks
This log:
Rebuild started: Project: blinky_pca10040e *** Using Compiler 'V6.21', folder: 'C:\Keil_v5\ARM\ARMCLANG\Bin...
Hello, I.m using SDK 2.6.1 with VSCode.
I created a new application based on the sample /nrf/samples/net/mqtt configured for nRF9161_ns which is listed as a compatible board...
Hi,
When I define my nrf52840 pin 0.19 as input put, and there is no connection to any sensor.
Then I use gpio_pin_get_dt() to get pin 0.19 status, the status is high...
I downloaded the nRF Connect SDK v2.7.0 and read the Release Notes. I installed the v2024.7.18 (pre-release) version of the nRF Connect for VS Code. As a first step, I created...
Greetings
I am trying to configure the nrf5340dk to use the i2c0 bus. I believe i2c1 is already configured, but for learning purposes, I want to figure out how to do this...
Hi,
When I DFU upgraded the bootloader of my firmware, I found that during the upgrade process, when ret_val = bl_activate() was executed, the pin would be pulled low. ...
The product page for the Thingy53 only shows hardware files for the v0.8.0 board revision, not the 1.0.0 or v1.1.0 board revisions.
https://www.nordicsemi.com/Products/Development...
HI all!
So I'm trying to use and modify parts of the Asset Tracker v2 application for my own project and when I created a new application with the pre-existing sample on...
Hello all,
I am trying to write some code to read the sensor values from two VL53L0X tof sensors, but I'm having some trouble.
My current code:
My devicetree:
...
I am using the cloud client example and connect to the nRF Cloud. I receive message fine on an interval and when I press the button.
I do not get any notification in my...
Hi all,
I am hoping to eventually integrate the crashlog functionality, but prior to this, I wanted to test the basic functionality with the flashlog. I have looked through...
