I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
I want to make sure I understand something fundamental. The nRF52840's PWM peripheral is hardware based unlike the app_pwm library which is software based, (originally developed...
We are currently starting a project with a nordic chip. We want to work with the newest SDK (2.x.x). We saw the new SDK 2.0.0 in the nrf Connect for Desktop Toolchain Manager...
Hi,
Shouldn't the comparability matrix for nrf52833 on package CJAA revision 2 be with a 'J 'not an 'I' for WLCSP
from web site
from product specification: ...
Dear Nordic Engineers
Our customers use the nrf_desktop application to develop their product.
They use the NCS 2.0.0\nrf\applications\nrf_desktop and build project on...
I need to generate a clean 10kHz sine wave. I tried using PWM ( https://devzone.nordicsemi.com/f/nordic-q-a/89209/clarification-on-how-to-generate-a-10khz-sine-wave-with-pwm...
Hello, I followed this tutorial in order to setup custom BLE service. The tutorial as is works correctly and defines one service with an RX write characteristic and a TX notify...
Hi All,
I have implemented sleep mode in the firmware. I am using NRF52833 in my project. When the device is in idle state it goes in sleep mode. I am able to wakeup my...
I tried adding DFU support to my application by following this official tutorial:
But, I get the following errors:
/opt/nordic/ncs/toolchains/v2.0.0/opt/zephyr-sdk...
We're using sd_flash_write() and sd_flash_page_erase() to store some data to internal NOR FLASH at runtime. We have these calls integrated with the RTOS we're using in a HAL...
I've been using nRF Connect for Desktop a lot recently for power measurements with the PPK2 and to program nRF52840Dongles. I keep stumbling over a small missing feature:...
Hello,
I saw in the documentation for the softdevice s132 v5.10 (which is for production use now), I saw it supports changeable MTU. I have searched for the maximum supported...
Hi all
I have a problem with allocate RAM.
I build the project as non secure.
in the zephyr.dts file, you can see that the memory is divided into 3 areas:
sram0_s...
Hi
I have nrf52833DK it was working all fine but suddenly the LED5 is not lighting up and it is not detected by USB port. I tried to check the board voltage regulators and...
Hello,
I just started working on the nRF52 series controller, I want to upgrade my project using BLE features.
I need 1 master device to send to multiple slave devices...
Hi,
According to CryptoCell-312 documentation , it supports the SHA-1 algorithm. I was able to successfully run the SHA-256 cryptography sample application in the nRF Connect...
