I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
hi，i use radio_test example for radio test. If I don't make any changes, the routine can run well, but a PA chip is added to my product to amplify the RF signal. The PA /...
I am getting a softdevice hard fault occasionally, on fully enclosed devices with no debugger port access.
Where can I find info on potential causes of this fault?
nrf51822...
Hi
I have a question about reset Bluetooth, how can I do that?
I don't want to reset the system only to reset ble, turn on and turn off the ble,
thanks and regards
Hi guys,
This is my first BLE project. I want to send sensor data from my nrf52840 dk to my dongle. I know how to make an advertise but I can’t find a way to send my sensor...
Hi!
We'd like to understand the most reliable way for DFU OTA our Nrf52840DK boards over a "serial" topology network?
We are using nRF5 SDK 15.2.0 and our configuration...
we have nRF52832 controller
now we would like to choose the softdevice S132 or S112
how can i select the softdevice?
where can i find the difference between S!32 and...
Hello, Technical support team
In the past, I contacted you to confirm nRF52832 application.
This time, I have a question for a external reset as follows.
My application...
Hey there,
We are working with NRF52832 WLSCP package,
We had stated certification process , for BQB testing need to use the Radio test example with UART between EUT...
Hi,
We are using Nordic BLE-NRF52833 Module one of our products. We are developing our own windows application(using C# language) to communicate the information to our Product...
Hi! Reading this ticket, and the nRF Connect SDK and nRF5 SDK statement , I understand that the PC-BLE-Driver, whether the Python or JS variant, are in maintenance mode, and...
Is there some example for Encode / Decode with AES algorithm in ECB and CBC modes using Segger studio?
For a start, I only need the ECB mode that should be implemented in...
I have checked the qDEC example, I don't know what it is doing, so I can directly say what I need. I connected a Hall sensor to two pins of 52840, and configured QDEC. I set...
Hi, I am just doing some testing using Nordic Thingy:91 and already available firmware and cloud. I am in the very initial stage of learning about it and preparing it for...
Hi,
I'm trying out an application from the NRF SDK where I need to connect via putty or something similar to the serial port.
However, the port is not showing up (normally...
Hi Team, In my project i am using nrf52833 and i have established a network using Open Thread protocol to communicate . I am able to pair my device with the network. One scenario...
