I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi,
With the NRF Connect SDK version 1.9.1 it is not possible to setup a Thread Coaps connection.
The DTLS handshake fails after Client Hello with an Alert message ...
Hi,
The below is our requirement for NRF5340
1. we have a DFU application with bootloader as an hex file
2. we have another app say blinky as an hex file
3. merge...
Hi all
My first post. I tried to finish one of Nordic tutorials. I need to use app from nrf connect(v 3.10.0): Bluettoth low energy (I have installed v3.0.1). I have nrf51DK...
got the thingy:91 following the getting started video had the bootloader updated and uploaded the right hex file for lte, the provided sim appears to be outdated so tried...
Hello, I am using the Asset TrackerV2 application (SDK 1.7.1) with the modem firmware (mfw_nrf9160_1.3.1). Recently the following error <err> aws_iot: getaddrinfo, error ...
Hello,
I have been developing on a nRF52832 DK using nRF5 SDK v17.1.0, and am very close to a production ready state. The final program will use soft devices, app_timers...
I want to develop a USB composite device using USB CDC ACM + USB Audio. I am not familiar with USB device protocol, so I hope to have a reference example. My development board...
I use the NCS version 1.9.0 with SES.I build and flsah successfully.I use the antenna array with 4x4,about 16 antennas.
In Tx,i use the Putty to debug serial.there is it;s...
Hi,
I have a hardware that I want to connect via BLE and send data via NUS (Nordic UART Service). I can connect to this hardware via the NRF Connect application on android...
Hello.
I get an error NRF_BREAKPOINT_COND. I use nRF5_SDK_17.0.2, s132_nrf52_7.2.0_softdevice and my kit - nRF52-DK.
An error occurs when trying to swap UART pins (Change...
Hello,
I want to establish 802.15.4 communication @ 1 Mbit between a nRF52840-DK and an ATmega256RFR2 based device. The communication works well with 250 kBit/s in RADIO_MODE_MODE_Ieee802154_250Kbit...
Here is the situation:I can read the accvalues by uart without the ble, but when I was trying to read the values on the phone with the ble, it didnt work. I modified the official...
Hi,
I use event manager and define semaphore according to https://docs.zephyrproject.org/latest/reference/kernel/synchronization/semaphores.html . How can i delete the semaphore...
Hello!
I have an incremental encoder such as this one: https://www.digikey.no/en/products/detail/cui-devices/AMT103-2048-N4000-S/10468125
I have to make this work with...
Hi,
I have loaded one of the basic samples( nrf connect SDK, fade_led ) into my nrf52DK.
Using the free run mode or the debugger almost everything seems to work correctly...
