But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
I cannot get logging in the Seggar debug terminal nor the J-link viewer application (All terminals) when running this example.
I have the NRF_LOG_BACKEND_RTT_ENABLED selected...
Hello
I am using nrf52840 from nrf9160dk, I am trying to run example from nrf52840 with sdk16.0.0 and sd7.0.0. While checking data on uart I am getting following error...
Hi
I'm trying to get a DFU boot loader working on our own custom hardware. My initial approach was to build secure_bootloader_ble using my own public_key.c file and try...
I updated my Thingy:91 today to version thingy91_fw_2020-04-29_bc7ade8b.
I flashed the mfwnrf9160120, the thingy91_nrf52_connectivity_bridge_2020-04-29_bc7ade8b and the...
Hi, I'm developing firmware for the trf7970a nfc chip. For standard communication the chip uses spi, but a special direct mode uses an additional two wire interface where...
Do the values for current consumption given for the scenarios in Section 5.2.1 of the nRF52833 PS include the current for any peripherals required? E.g. the PS quotes 2.6uA...
Hi!
I am trying to merge the basic/button sample with the mqtt-simple sample.
I added to the prj.conf of mqtt-simple sample.
My main.c looks like this:
After merging...
Hello!
Iam trying to get the spi function to work properly on my thingy 52 device.
My problem is that the transfer wont stop when it should in my opinion, i have analyzed...
Situation: SES, SDK 16, nRF52832
I'm developing a pre-production test program without BLE. I'm using APP_TIMER_V2 and noticed that the timer events do not not happen even...
We have a custom board with nrf9160, ncs 1.2.0 and modem fw 1.1.1. We experience strange behaviour with the GPS: As an example,on units with 30 min fix intervals, we experience...
I added the commissioning part from the nfc_meshcop example to the mqttsn_sleepy_subscriber example. I tested the nfc_meshcop exaple and worked, so the border router part...
Hi,
I have developed a project of mine based on the nRF52840 DK and now I want to place
the nRF52840 chip on my custom 2 layer PCB board but I think that it might be very...
We still have some Problems to use the Supl client Library, to test it we use the normal GPS example and seems like the connection is available with NB-Iot settings. We are...
I have a product which uses the nRF52840 SoC that will also have NFC functionality. The housing of the PCB is sort of forcing a custom design for the NFC Antenna.
We need...
