Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
I'm using JLinkRTTViewer to look at RTT output from my code. The problem is that when I try to go into POWER_OFF, it generates a reset instead.
Is there a way to go into...
hi,
We want to position with aoa(angle of arrival) method, can it provide the One IQ-sample is a pair of in-phase and quadrature-phase samples, and Phase and amplitude information...
Hi,
I am using a nrf52840 development kit flashed with the ICMP example provided in SDK 15 and I am using a device with Bluez tools version 5.47 to connect to it.
However...
While investigating problems I'm experiencing with bootloader_secure I believe I've identified an error in the HCI TX finite state machine ( components/serialization/common...
We have implement a PPI for device match to trigger a GPIO toggle . but now we want to trigger a SW interrupt or a callback function .
my question is how to set PPI TASK...
Hi,
I merged UART exam ple from nrf5 sdk v14.2 with light switch client example from mesh sdk v1.0.1, i have 2 boards client board which is nrf52832 and server board which...
I'm developing an application using the NRF52832. Im using the ADC, and there may be times where the NRF52832 has 0V on its supply pin, but the voltage on the ADC pin is nonzero...
Dear Nordic Support,
does the BLE Uart example (SKD 14.2) inlcude any data link layer machnisms, for example error detection & correction, collision avoidance?
I implemented...
hi to all,
i am developing a ble device with nrf51822 and i encounter with a problem, in my program i have code like below :
in this point program work well, but when...
Hi
I'm facing a problem with light switch demo from mesh SDK v1.0.1, when running the light switch client, as shown in the rtt viewer below the configuration of the server...
My customer is modifying the code based on the example provided in the SDK 15.0.0 to suit their project:
Project file from the SDK under \ nRF5_SDK_15.0.0_a53641a\examples...
Hi,
I am making a project with the nRF52832.
In this project i must configurate another chip with SPI.
The timing must be very accurate. Now the problem is that the...
Hi Team,
I am using nRF52832 to implement smart watch product and it is now close to PP stage.
Currently our product testing engineer found that in a relative noisy environment...
HI. I used a translator.
I want to control the mouse and keyboard using HID with the nRF52840 PDK.
I found the HID example in SDK15 and compiled it
The Infocenter...
Hello,
The sd_softdevice_enable never returns, how can I investigate please ?
With my Jlink probe, it's look halted at address 0x000008CC.
Configuration:
SDK 15...
