I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
I am working with an nrf9161 and I can see that the IMEI is not programmed and likely causing my connection issue. I only have the modem connected to an rtt and nrf5340 what...
Hello community,
I am developing a device that uses the NB-IoT network . I would like to know if the NB-IoT module of the nRF9160 supports SMS . If it does, will it provide...
Dear Ladies and Gentlemen,
We have recently started comparing the BM833 (and the corresponding nordic devkit nrf52840) with an other hardware (ESP32), neither uses amplified...
Hello everyone,
please take a look at my minimal reproducable example, which explains the problem and also includes some example measurements. derteufelqwe/nrf-ble-datarate...
Hi
As mentioned in the datasheet, UARTE can operate up to 1Mhz. Is there any special condition/factor to achieve this?
and how fast can a regular GPIO operate?
Thanks...
Computer : Mac Book Air M2
OS : Sonoma 14.5
Hardware : SEEED XIAO nRF52840 Sense
I am building my software using nRF Connect VSCode Extension, while when I select my...
nRF5340 NCS 2.6.1 nrfjprog 10.18.1
My project is based on coap_client and also uses MCUBOOT.
I can program both cores using VS Code, and I notice it splits merged_domains...
Hi,
I am using a nRF9161-DK to flash and debug an external nRF9160 board connected via the nRF9161-DK DEBUG OUT 10-pin connector.
In VS Code "CONNECTED DEVICES", I can...
Hi, I am currently working with the NRF52832 on a custom board that is working with a timer for a particular sleep interval now I have added an external RTC module, and i...
Using nrf9160 with W5500 Ethernet NCS Version 2.6.1
My normal MQTT connection is working fine, but connecting to aws is being an issue. I am getting mqtt -22 error. I...
Hi. I wrote a firmware on nrf9160(SIAA chip), but it doesn't work. On the hardware side, the circuit is same as that of nrf9160-DK, CTS and RTS is short respectively.
If...
Hi,
We are using two nRF54l15-PDF to communicate as SPI, one is in master mode and one is in slave mode. The master device sends a simple array of bytes, the first one being...
Hello,
I'm currently working on NCS2.6.0 and ANT sdk v1.3.0,
I would like to know is it possible to do BLE scanning(without connection) and ANT+ heart rate searching at...
