Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hello,
I designed a PCB using nRF52840 for controlling the board.
I have physical access to the following pins : SWDIO, SWDCLK , VSS , VDD , nRESET.
What is the boot...
Hello,
I am trying to exchange data with an external slave sensor via SPIM communication using the nRF5340DK.
I am currently facing two main issues:
1. The spi_transceive...
I am using the NRF54L05.When I was using the timer function of the Zephyr software, I created a timer with a 10ms cycle. After my system had been running for a long time ...
ncs: v3.2.0
chip: nRF54L15
If I set CONFIG_PM_PARTITION_SIZE_MCUBOOT=0x10000 (64K), MCUboot fails to boot, and the error displayed is: 'Protect mcuboot flash failed...
Hi,
Can you please guide me if I want to receive a larger message of around 15KB from server, how can I do it using CoAP block transfer in thread.
I am using nRF5 SDK...
Hi,
I built the nrf/samples/bluetooth/hci_lpuart program in SDK v3.1.1. I am using an nRF9160DK board version 1.1.0. I did add several printk statements to zephyr/samples...
Hi Team,
We are working on a commercial pre-production project using nRF5340 and are currently migrating from nRF Connect SDK 2.6.1 to NCS 3.1.1 . We followed the official...
I have several hardware pieces based on the Fanstel WM02C nRF7002 module (nRF54L15 host) and am having problems connecting to WiFi networks on a subset.
All modules successfully...
nRF54L15, Zephyr +MCUboot. I am unable to redirect LOG_INF() output to RTT.
prj.conf
Can you tell me what is wrong? How to force logger to output to RTT?
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
We are trying to pass interrupts at high speed (clock signal) running at 800khz from port p1 to signal the RISC-V Co-processor to trigger a capture on a 4 bit bus. Is it possible...
Hi,
using nrf connect sdk 3.11, nrf54L15-PDK
I am testing low power with development board, I am trying to reach low power 2.9uA as bench marked.
When GPIO (button)...
I noticed in SD7 SDK16.0.0 when CENTRAL and PERIPHERAL connections are defined, the soft device will return designated central and peripheral connection handles. For example...
Hi,
We are modifying our existing product and adding PA to increase the range. Device right now is developed with nrf5 SDK, but we have plans to move to NCS. However manufacturer...
hi support team,
customer is using our 54L15 for mesh lighting project, here are three questions:
1.
customer needs timer model, i see the "time_cli.c" and "time_svr...
