Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi,
I'm using GPIO pin as input button with nrf9160 using Zephyr RTOS, but when I was press the button I didn't get any response from button state.
hear is my code
...
My query is:
1. Is it possible to access the azure using WIFI network in above application?
2. After knowing the IMEI using AT Command, in response to which event should...
I am getting more current consumption when internal pull up resistors of nRF52832 are disabled and external pull up resistors of the slave sensor are enabled as compared with...
Hi,
Currently, I am building an application with Bluetooth mesh and I tried to use Zephyr's logging v2 modules. However, when I build it I get MPU-fault errors at boot....
Hi,
I saw in ozone that SW crashed with hard fault explained as escalation of exception that was not enabled.
How can I enable all exceptions to see the exact reason of...
Hello, I'm using nrf52833, pca10100.
My project is based on 'ble_app_uart', and I added buttonless DFU project.
this is ble_dfu_buttonless_async_svci_init() function...
I have succeeded in running the Multi-NUS package on the nRF52840DK. My client's client learned of the nRF21540EK and wants to try using it to extend the range in the present...
i cannot seem to select nRF Connect SDK when creating application in vs code. i already install the nRF Connect SDK v2.0.0 from the toolchain and the nRF Connect Toolchain...
I am trying to build a example program in KEIL for the nRF52832 QFAA device. When I sart KEIL the program shows a massage that says the nRF_DeviceFamilyPack.8.3.1 is required...
Good day to all I am trying to change the Application on a device with an nRF52832 chip with an existing firmware. To do this, I use nRF Connect for Mobile 4.25.3. From the...
I am developing GATT Server Reader Firmware usng nRF SDK COnnect using NRF52840
I have implemented two services in reader FW in two files say: service_a.c and service_b...
I have tried installing the nrf connect 3.11.1 on 2 different windows 10 machines. Both are clean windows 10 installs. The hard drives were wiped and windows reinstalled....
Hi,
the following event is generated when I connect two or more nRF9160DKs to a Windows machine: "Disk 2 has the same disk identifiers as one or more disks connected to...
1. 2. 3.
I am using the ble_app_beacon example as the starting point for my project. I am working on a project where a number of beacons will advertise its identity and...
How do you enable any of the i2c peripherals on the nRF9160 dk boards?
I tried changing the device overlay to the code below:
& i2c0 {
status = "okay" ;
compatible...
