I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
Hi, i'm working with NRF51822, and i saw on reference manual that micro enter in the SYSTEM OFF mode. The problem is i dont want the micro enter on this mode.
I make de...
Hi,
I'm working on a project using the gazelle protocol with the gazelle pairing library. Due to the fact that I use the GNU GCC compiler, I created a Makefile from the...
Dear Nordic team,
We have designed custom boards with nrf52840 chip. We observed that in one of the boards the application is not running until the swd pins of the custom...
Hi,
We are using laird BLE653u BLE module in our application. This module has nRF52833 BLE SOC. We have ST Link V2 as a programmer tool. We want to use SWD protocol for...
I have a project using NRF52840 as master in BLE central to scan BLE device.
I found all example will connect device automatically when device found
I would like to change...
Forgive me if this is already discussed somewhere - I'm fairly certain it must have been - but I can't seem to find what I'm looking for. My client's project uses a higher...
Hi,All:
As the topic,which address is the mbr jumping to bootloader by ?0x10000ff8 or 0x10001014? and how to feed the mbr para register 0x10000ffc and the 0x10001018?
Hello,
I need to use the more accurate HFXO for a very short interval to time incoming interrupts (approx 1/50 second every 15 mins)
The processor sleeps idle for the...
Dear DevZone,
I am trying to configure the SAADC on my custom nRF52840 board.
I would like to use it in blocking mode together with oversample 16x and burst enabled...
Why is SES throwing an "Illegal value 0x21009168 written to register 66 (MSP_NS) ignored" message after "Download successful" when programming nRF5340's network core with...
Hello everyone,
I have questions concerning direct advertising. I have read this and other posts from several years ago which provided some useful information.
devzone...
Hello,
at the moment I am trying to get the NRF9160 Icarus Board to communicate with an ESP8266 Board within serial modem mode. I just need to send some AT commands through...
I am trying to install nRF Connect SDK v1.6.0. For some reason the download speed is extremely slow, and even fails without the ability to resume automatically. On two occasions...
I am having issue configuring the chip select (CS) in my little test program. I have read through the SPI drivers and debugged through it and from what I can tell I have everything...
As in fds.h, i am using the fds_record_update() function to update a record, and then as soon it is completed, i want to read the updated data from the flash, but how do i...
