I'm using QT + QBS + bare-metal + gdb + openocd + stlink(debugger). I want to print into qt-terminal debug information. How Can I do this feature?
forexample:
int main...
I ran the ble_aci_Tranport_layer_Verification.ino sketch from the Nordic BLE library and I get no output to the serial monitor after "nRF8001 Reset Done" is displayed. I think...
I am trying to debug my code today and am finding that Eclipse is constantly breaking execution at the INLINE function app_timer_evt_get(). I do not have any break point set...
Hi,
Recently,
the DFU of the "Master Control Panel" (Android) can not complete the upload mission.
But,
the DFU of the nRF-Toolbox in iOS is
work well.
Old...
I just tried out the new iOS nRF Toolbox 1.5 and it doesn't seem to handle long init packets.
I gave it a zip file that contains a 137216 byte 'application.bin' and a 192...
Hello everybody,
In the SD_EVT_IRQn ISR I check for BLE and SoC events and set flags for each so my application can fetch and dispatch the events in the main context. ...
Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
I am using Nrf52 DK as a J link programmer to program Laird BL-652 which is connected to NXP LPC 1519 via RX/TX Pins. I am trying to send commands from BL652 to NXP via UART...
Does anybody develop bluetooth JOYSTICK?
Could you please help me with some code samples to understand how to do Joystick on NRF products.
Best regards.
Hi
I am setting an interrupt off the RTC to cause wakeup from nrf_pwr_mgmt_run(); This is to conserve power. My code is working but the times are out by an order of magnitude...
Hello,
Will there be a migration guide posted for v15.1.0?
What is the suggest path of upgrading from v15.0.0 to v15.1.0?
Is it generally suggested to upgrade to new...
Hello,
I have not seen any mention of a BlueZ based BLE DFU library other than here , which was a long time ago.
I will require this library for my current project so...
Hi team,
My customer needs to make some adjustment on I2C frequency due to their SW requirement. As our reference on datasheet, I2C frequency needs to be 100kbps, 250kbps...
Hey, i want change the simple_on_off model a little bit, so the server return an byte array to the client get_message, can you say me how to include vendor specific model...
If nrf_gzll_ok_to_add_packet_to_tx_fifo() returns false and nrf_gzll_get_error_code() returns nothing, what does this mean?
Facing this a lot when trying to change channels...
Hello,
I was trying to perform DFU over mesh. My setup was as followings:
7 nrf52832 Devies. One of them is connected to my laptop.
I programmed those according to this...
Hello,
I'm using the nRF51422 with a dfu dual bank bootloader with SDK 11. I can programm the uController with the Softdevice and the bootloader and afterwards load successfully...
Hello, I'm trying to add a Peer Manager functionality to the Mesh Provisioner application.
I'm using nRF52832 devkit, Segger Embedded Studio, nRF5 SDK for Mesh 2.0.0 and...
Hi,
for some reason I cant debug in Keil, the program doesnt stop in main.
I also have NRF_LOG enabled, but nothing appears on RTT.
What could I do?
Thanks!
My environment is:
Windows 7
JLink Plus v9.3
IAR EWARM 8.30.1
SDK 15.0.0
Softdevice S132.
My hardware is a custom board with a Rigaldo BMD300 module (contains...
Hello,
I'm trying to modify the dfu_dual_bank_ble_s130_pca10028 bootloader so my device would start with the application and after a signal (with the button) it should...
I have an application where a unit contains a nrf52840 and will act as a central device, collect the data from peripheral device and store into the onboard memory. Upon the...
