i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
From document [Getting started with the nRF52840 Preview Development Kit]
( www.nordicsemi.com/.../Getting-started-with-the-nRF52840-Preview-Development-Kit)
we know that...
Hi,
I'm looking for a BLE device to work with an arduino and to speak with a smartphone.
The point is that the connection should be made by the user via the smartphone...
I am using nrf52 with sdk11. I have set the advertiser data as Manufacturer data in nrfConnect app in my android phone. So that whenever the data from my phone is advertised...
Hi.
I try run "ble_app_hids_mouse" example from nRF5_SDK_11.0.0 in nrf51422 (nrf51 dongle).
Previously i ran this example in nrf52 (nrf52 DK, s132 SoftDevice), and all worked...
Hello!
We use chip nrf52832(QFN-48) in our project and we wont to pass the PCB certification.
But we also want to use chip nrf52810(QFN-48) in another project, but with...
Hi ,
Please advise, what the Low Power option I have if I want to sample Two channels of analog input at the same time. The sample rate in every channel is 12K, 12Bit....
Hi I am using SDK12.2.0 and Softdevice S130 v2.0.1 on board PCA100028 ; the board works fine and Phone can scan the name of DFUtarg； But when run the same on the customer...
Hello, I'm planning to try the NordicBlog; Capacitive Touch on the nRF52 series to test a button type or a up-down slider type .
I'm planning to use an nRF52832-QFAA for...
Hello,
Can you please provide any link or give me any advice how to connect NRF51822 chip with NRF51DK?
Here is my connection that doesnt work:
DK GND DETECT and GND...
float f = 1.234;
NRF_LOG_INFO("My float number" NRF_LOG_FLOAT_MARKER "\r\n", NRF_LOG_FLOAT(f)));
How to simplify this way to show float number by uart in sdk13.1.
In...
I have 2 questions regarding BLE5 on nRF52832
Which Soft device and SDK has to be used to implement BLE 5 on nRF52832? We will be using the nRf52 DK for same.
Is the provision...
Hi,
I am using timer interrupt in my code. In that I will be generating interrupt after certain time interval, after the interrupt it should process the incoming data from...
Hi
We are using the nRF52840 and the application is OK now. Then I do the OTA using a Android phone which supports Bluetooth 5 and it's made in our country. I use the nRF...
