Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
I'm having trouble activating a PDN on a running/connected device. Here's the code:
Seems like I'm missing something here. pdn_init does get called on system setup...
Hi,
Just wondered about the following ....
Strange parts of this code ... Or things I don't understand
After the first READ in Setup() it successfully reads the data...
I am trying to implement a simple uart echo test using nRF21540 DB board, but I always get NRFX_ERROR_FORBIDDEN when trying to transmit.
This is the initialization code...
I am using nRF5 SDK v16.0.0 on nRF52832. IDE is SES. I am also using FreeRTOS
What order should the following methods be called in? Does it matter when fds_app_init is called...
Hi Team,
I am using SEGGER 5.4 IDE and NRF52840DK controller.
I did not understand the difference between Terminal Emulator and Debug Terminal in Segger IDE.
I am not...
Hi,
I want to configure Timer1 (32 bit ) to run up to 1 sec and then reset. I want this to be done continuously with the help of Short but without using the event handler...
Hello, I have an nRF52811 on a custom board and have been having some issues. I have a nRF52840DK which I used to flash the custom board (while powering the board with the...
I connected it to an external mcu as shown below. After downloading serial lte modem to nrf9160,
at command is sent, but it does not respond. Connect only 3 pins for communication...
Hi I am using the nrf52832 with zephyr os , NCS 1.9.1 , also using the external flash as a secondary slot, using a nor flash I tried to upgrade my app but i an error occurred...
HI, I am trying to develop a project with multiple UART facilities, and I have put the code from the following link in my project.
However, the software UART didn't work...
Dear Nordic community,
I am currently trying to send ADC sensor reading to MQTT broker(hivemq). I have successfully sent some data to the mqtt broker. However, the reading...
Dear all,
I'm trying to build a system with 1 central to 9 peripherals. All devices are based on nRF52832, SDK16, s132 7.0.1.
I've checked this post to get some clues...
Hi, I'm having some trouble with a custom board based on nRF52832.
I need to use NFCPINS (P0.10 and P0.9) as GPIOs. As IDE I'm using Keil uVision.
The code works weel...
Hello! We are having a problem getting the HFXO to start running in the Murata MBN52832 module (nRF52832-based) so that we can start advertising. The 32MHz crystal is embedded...
I'm having trouble reassigning the pin value for the LED's in the connect SDK. I am using the base PWM Blinky example and have changed the pin value assigned to PWM_LED0 in...
