I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
When using nrf51-ble-driver_win_0.3.0 with Visual Studio 2010, after I put a breakpoint in my code, when I try to have the process "continue", I always get unandles exception...
Dear sirs,
Many thanks for the IoT SDK.
Just setting up the Raspberry I can't start the Phyton CoAP example as defined in documentation.
The envirinment is:
R...
Hello everybody,
I'm getting crazy, I'm trying to extend HID axis values from 0..255 to 0..1023 max using the descriptor found in the example ble_HID_keboard/hid_joystick...
Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I am using the v1.0.0 sdk at_client sample project with the v1.0.0 LTE Link Monitor on an 0.8.2 nRF9160-DK board. I have upgraded the modem firmware to 1.0.0.
The AT%CMNG...
I am trying to transfer data from a USB to serial converter board (called board A) to the nrf5 board (called board B). I made the connection over a bread board, the transmitter...
hi i'm use nrf52dk
and segger embedded studio
also i'm mcu beginner
The value was obtained using a magnetic sensor.
now i want using the ble
Now we want to send...
Hi,
I started working with nRF9160 and took AT_Client and added support for my own commands. Additional to that I added HTTP example to it and they are working great together...
Hello,
i have a very easy goal, i want to generate a hex file which combines all parts and flash it via nrfutil or something like that onto the device.
I followed a few...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
Hey , i'm using nrf52832 with SDK 14.2 . I'm trying to send 3-axis accelerometer data through BLE . Is there any example for SDK 14.2 to achieve this ?
Hi,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image. I am using ‘ble_app_blinky’.
As shown in below snapshot I am just doing below...
According to the blog below, hardware design of nRF9160-SICA has been fixed on May 31st. https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/nrf9160-development...
I am designing a pcb just the nRF 52840 MCU. The design of the PCB is based on the reference design from Nordic. When ordering the PCB I came across a problem that the vias...
I have 4 gpio inputs on the nRF52840 working and sending these states over the BLE. I tried to add a few more gpio inputs but I get an error =4 which I think is NRF_ERROR_NO_MEM...
Hello,
I can successfully put my nRF52832 into System OFF mode, however, the Debug Mode Interface is still running, so the current consumption is > 2mA. What are the command...
I have a nRF9160 DK need to update modem firmware to v1.0.0
According to C:\nRF91\mfwnrf9160100\README.txt below, I should use nRF Connect Programmer to update modem firmware...
In the light_switch example of nRF5_SDK_for_Mesh_3.1.0, I noticed that generic_onoff_client.h has a union for holding the current message packet. However, there is only one...
The timer example with SDK 15.0.0 uses the old timer driver. Is there any example code showing how to use the current nrfx_timer?
I'm just trying to generate a periodic...
