Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hello, I have a problem with the bluetooth connection to a Samsung s21. It connects for like two seconds and then disconnects immediately. Then tries to establish a new connection...
In build configuration i need to select nordic board . i have been using fanstel bt840 use nRF52840 QIAA, ARM Cortex M4F, 64 MHz . what board i have to select in this ? or...
Hi, we're having some problems and need help. We have a usage scenario: in HOST mode, the switching rate is 250k/2M every 10ms, the time slots of the two rates are different...
Hi I am trying to interface QSPI with NRF5340 dk board. I am getting build errors. I have used SPI-FLASH sample and it was working fine and I am trying to change the SPI-FLASH...
Hi,
in the new version of nrfx there is a function (nrfx _uarte _rx _new _data _check ( &uarte _instance ) , and how to get a similar result for the older version of nrfx...
Hi,
I have been testing the CAF click detector module and I find that any event callback after the click event takes almost 1000ms. That is the time between the actual click...
We are working on a project, with a working secure buttonless bootloader that works flawlessly. However I recently made it with bonds, and it works with all of the devices...
I'm experimenting with the Bluetooth Throughput sample in NCS v2.6.1. As I increase the distances between devices, I see strange gaps in the transmission from the Central...
Hello, when testing the BLE sniffer with an nRF52840 dongle (utilizing the most recent official sniffer firmware), I configured Wireshark to capture the coded PHY. After initiating...
Hi,
We are working on integrating nRF-Mesh-Library (iOS and Android) sdk into our app for mesh networking, it should support identifynode, provision, add app key and add...
I found a similar thread, but it did not solve the problem. When CDC-ACM is enabled in Device Tree, the dfu-util application cannot find the USB port. The Bootloader started...
Hi everyone
I am using nrf52840 costume board. and using NUS ( Nordic Uart Service ) as the basic start sample.
My desire:
1. UART0 and UART1 work in async mode with...
If I enter the prj.conf settings according to the lesson text then the firmware crashes with different provisioning functions from the smartphone app such as forgetting a...
It's looking more and more like a lot of my problems relate to a weak cell signal. Is the RF front end on the devkit known to be inferior to a normal cellphone? My personal...
Hello, I have connected a LR1110 module to a nrf52 (PCA10040) development kit using Arduino connectors. Anybody written a simple application regarding the interfaces?
It...