Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hello,
I'm trying to create a long range IAS ( Immediate Alert Service ) unsing long range BLE 5.
On the server software I forced the PHY to BLE_GAP_PHY_CODED. I saw in...
The 'Debug Out' on nRF52832 (and 52840?) Dev Kits only works at 3V - so won't work with a 1.8V target.
The question has been asked before, and the obvious answer given ...
hi,...
i am using nrf52382 and nrf52840 ... one is client and server . i am using mesh sdk 3.1 .... i have debugged the example light switch server and client respectively...
Hey
This is sumanth. I have worked on mesh beaconing example and saw the output of continuous scanning advertisement of nearby devices in RTT, I made changes in light_switch_server...
I need to configure 1 device as relay node in order to relay messages from the client node to the server node. To test that the sever is relaying messages i could lower the...
Hello and thanks for your help,
We are looking forward to build a low cost and power wireless application using 802.15.4. We do not need any other protocols.
Am i right...
We have an NRF52 set up as Central, connecting to a peripheral (not our own) that's sending notifications with Data>20 bytes
I'm trying to differentiate between it sending...
Hello everyone,
I'm trying to set up entirely open source project for my NRF51822 chip. Everything works fine so far but something strange happens during debugging.
I...
Hello support team,
I am using your product through a module vendor and I have a question regarding errata 197. If the DC/DC regulator only has problems in low power states...
hi... i am using nrf52840 and nrf52832..... mesh sdk 3.1 latest version ....
in this case i am using client as nrf540 and server as nr52832 .... i have debugged the light...
Hello, We planned use nRF52840 in our project, and I have some questions about this MCU. 1) Is it possible to process signal from 8-GPIO with frequency of request 32MHz? We...
Dear,
I am testing nRF9160 DK with iBasic SIM, FW: SecureBoot and AT Client
I am trying to send SMS to my phone. I see : https://devzone.nordicsemi.com/f/nordic-q-a...
Dear Sir,
I am working with
SDK --- nRF5_SDK_15.0.0_a53641a
softdevice -- s132
nrf52832.
I was working with example codes in the SDK folder.
I am working...
Hi,
I need some help calibrating my moisture sensor analog readings using 3.3V regulated power source (VDD = 3.3). Here is my set up, borrowed from the proximity example...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
