Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Specifically, sinking a Cree C503B green LED (Vf 3.2V at 20ma) from a GPIO configured for high drive, without a current limiting resistor, from VDD 3.6V?
Figure 23 “GPIO...
Hello All
We are using nordic thread sdk's sample simple coap client and server.We want to ON/OFF LED of coap client from coap server.
Can any one help how we can achieve...
In SDK13, the initialisation of the low frequency clock used to be done within sd_softdevice_enable . In the SDK14 version of nrf_dfu.c , the LF-clock is already initialized...
Hi, I want to use the AES-CCM of nRF52832. But it can not work with the softdivice. I have read the following question and answer.
https://devzone.nordicsemi.com/question...
Hello All,
I have a peripheral device where one service with 4 characteristics is implemented.
Out of these 4 in 3 services notify is enabled.
Now I want to subscribe...
I have a situation in which a central device (A) must be able to receive from a power constrained peripheral (B) with very low latency, but likely at long intervals.
To...
Dear Nordic,
I tried to download the new SDK nRF5-SDK-for-Thread from here:
www.nordicsemi.com/.../60504
However, when I clicked on it I only got the TTM 0.11.0.
...
Hi every one ,
I am using NRF51822. I download the code
from this link. github.com/.../nrf51-ble-tutorial-advertising
I able to flash the hex file & see board are...
hi~
i am working with nrf 51822 with custom board and softdevice s110.
i am using is7020-a20 temperature / humidity sensor via twi (i2c)
i tried 2 versions of twi example...
I followed this guide , I'v managed to run make files and flash them using the terminal, then when trying to build the project in Eclipse, I get this :
Make: no rule...
Hi,
I am following the "Bluetooth low energy Services, a beginner's tutorial", however, this tutorial is written for SDK V11.0.0 and I am using SDK14.1.0, softdevice 5...
Hi there!
I've followed the guide to Eclipse GCC (using OSX) from here: devzone.nordicsemi.com/.../
I had to add some stuff to main.c to have it built (e.g. BSP_LED_APP_TIMERS_NUMBER...
Hi, I'm having an issue with some PCBs I've designed with the NRF52832 on a module. When I first connect the board through a j-link, the device is not detected in NRFgo studio...
Hi,
I wonder CRITICAL_REGION_EXIT() in app_sched_event_put() have to be moved to the end of function.
CRITICAL_REGION_EXIT() is called after proceeding index in current...
Hi everyone,
I am trying to port freertos on the nRF52832, but it is blocked in the vPortSuppressTicksAndSleep function. Below is the code for configuring the system and...
