I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
I am using nRF Connect SDK 3.4.1 on three nRF54L15 devices:
A ───────── B ───────── C
A–B: A central / CS initiator
B peripheral / CS reflector
B–C: B central / CS initiator...
Hi,
Does Nordic offer, or have plans to add, a FIPS 140-3 validated cryptographic module directly in the nRF Connect SDK for the nRF54L15?
We are evaluating the wolfSSL...
Dear Support Team, We have developed a product based on the nRF5340, using the Insight SIP ISP2053 module. So far, we have built approximately 25 prototype units and around...
Hello,
we have a custom PCB with the NRF54LM20B (nRF54LM20B_xxAA_ENGB) and nPM1300, and we are observing odd behavior with the LFXO failing to start from a cold boot, causing...
Hi I have a NRF52833 module in my PCB design. Are there any end of line tests you would recommend at the end of my production line?(end of line tests) I am using a Panasonic...
Hello,
I am trying to get the Nordic MCP to work in VS Code, but every time I try to authenticate, I get the following error:
I am signed into my My Nordic account and...
Hi,
We’re Hydro-Guard, a volunteer student team (TU Delft / University of Milan) building solar-powered acoustic recorders that detect illegal boats in nature parks ( short...
Hi
We are developing a system where 2 devices (NRF52840) advertise to each other (and eventually connect) in a highly reflective environment (the cargo hull of a ship)....
I am developing a proprietary 2.4 GHz distance measurement with two-way phase-based ranging and RTT on the nRF54L15.
I intend to control the RADIO peripheral directly, without...
Hello,
I tried following the exercise until the part where you start a debugging session. I looked at the thread viewer and the result was different than what was on the...
An nRF7000-QFAA (QFN48) is used in a 2.4 GHz-only scan design: one antenna on TXRF<0> behind a 2.4 GHz band-pass filter, no diplexer, no 5 GHz path. Scanning is restricted...
Hello Nordic.
Hardware: nrf54lm20A-DK v0.3.4
SDK: 3.4.2
sample: spi_flash
Initially, I tested read/write operations on an external flash using the `spi_flash` example...
Hello,
I am developing a custom Matter 1.5 application on an nRF54L15 using NCS 3.2.1.
My device exposes multiple Contact Sensor endpoints:
- Endpoint...
Hello.
When I ran the NCS SBOM command using VS Code, the following error occurred, and the file could not be generated.
I would appreciate it if you could tell me how...
Before buying two nRF54LM20-DKs, I need to know which way is supported. Our own protocol uses RADIO directly: in each 20 ms period a SYNC goes out at 30 µs, started by a TIMER...
