Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
SoC: nRF5340 SDK: nRF Connect SDK 1.9.1
CMAC calculation works fine with SDK 1.7 and SDK 1.8. But it failed with SDK 1.9.1.
psa_mac_sign_setup returns error = PSA_ERROR_NOT_PERMITTED...
Hi, I'm pretty new to microcontroller programming so please correct my wrongs.
I'm using the Libuarte driver library to have the pca10040 talk to my server via serial connection...
Hello,
Fllow the guide of Configuring and performing DFU over Mesh,I can update firmwre successful use DFU:
Source: Example/Dfu
Target: Blinky(about 180 segment)
But...
Hi, I am working on custom board with nrf9160. I want to use LTE LINK MONITOR but my uart don't work. I create simple helloworld application from samples. I change uart0 rx...
Hi,
I want to create 1 hex file that will contain my bootloader, app and softdevice.
I know i can use NRF GO studio in order to read each hex individualy but it is of...
Hello,
I am using PCA10040 development board based on nRF52832, Softdevice 6.1.0 & SDK 15.1.0.
On the Nordic website, I have verified that Softdevice v6.1.0 supports Chained...
What is the best practice for protecting against ESD for unused pins, should I leave them floating or ground them? I noticed in other posts here that it has been recommend...
Hi!
I use HID example and try to understand in a hid service init for why report_map_data[] with a table.
What is do this array? If I use keyboard example, I should get...
Dear Sir,
I am working on nrf52832.softdevice S132. SDK15.
I am getting the following messages when I try to connect to the peripheral using nRFConnect.
The error is...
Hi,
we are testing nrf52840 together with rfx2411n amplifier to extend the range.
The problem is that we have same range and same RSI values when testing with bypass mode...
Good afternoon,
I have purchased multiple nRF52840 Dongles and so far have successfully ran blinky peripheral and master (required to adopt PCA10056) examples.
I tried...
Hello Nordic
I am testing SEGGER EMBEDDED STUDIO and I think it is little buggy.
When i simulate NRF52 application without actual device (I can not
debug on hardware...
Hi,
I used SDK_15.1.0, secure_bootloader/pca10040e_uart.
Through PC uart,it update successfully .But boot through android(linux) uart,it returned 'invalid crc'.Can anybody...
Hello,
I am working on BLE Peripheral and Central part on SDK11 for a long while. Now i want to start with NFC.
I tried to go through nfc section in SDK14 but could not...
I am observing a surge startup current of 0.1 to 0.2 mA when I am powering the nRF24LE1 module. Is it possible that the device can startup in power saving mode? Is there a...
Hi
I had used one nRF52 Kit(nRF52832+nRF5_SDK_14.2.0) to connect a BLE 6LoWPAN Border Router(Raspberry Pi 3B+Raspbian)
according to the IoT User Guide.
But in IoT applications...
i am using ubuntu 16.04
using eclipse photon IDE
nrf52_14.1.0 i am unable to run to run more than two threads can u please help me out in this
i am trying "nRF5_SDK_14...
Hi,
I am working with bonding process on Android App.
My problem is:
When I create bond to nrf51822, the process complete successfully. Then after a few seconds (3-5...
