i just rebuilt the code in the beacon_advertiser.zip file attach to this issue for the NRF52232....
the code runs as expected, though consumes about 200uA when sleeping...
We are currently working on a project based on Enhanced ShockBurst (ESB) and would like to use Front-End Module (FEM) support with the nRF21540.
In your Enhanced ShockBurst...
I made some tests with PPK-II in source meter mode by connecting a load resistor in series with a Fluke 8846A ampere meter to the PPK output. A also hooked a GW Instek GDM...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
I want to realize the connection and communication between the broadcaster and the upper computer software nRF Connect...
Hello,
I'm currently trying to integrate the Android-nRF-Mesh-Library in our App.
Identifying works fine but when the library tries to send the public keys to the node...
The nRF54L series is a new device to the nRF family, and during the bring-up of the chip from early engineering samples to mass production devices there have been quite a...
Hi,
I have tried the BLE image transfer demo and I really want to have the similar function about the real time data rate calculation. How could I do that? I found there...
Hi,
We are using nRF52840DK. Our main object is to collect the log for the BLE. We have installed the nRF Sniffer software and wireshark tool to extract the BLE Packets...
Hi,
We are using nrf52840 QFAA with our amplifier that gives ADC values at 100hz. We need to process the data via low pass, band pass filters, median filter, moving average...
Hi, i am using nrf5340 which has flash memory of 1MB. but my application is exceeding this memory size. what I want to do is to merge the image 0 and image and make it as...
Hello everyone I am gradually learning Bluetooth, it takes time, but I need a temporary solution, I need a so-called adapter, Bluetooth <-> UART, to simply transfer bytes...
Hi all,
I develop my own IoT board using NRF52840-QFAA (Rev3), I am follow the Intermediated Course about Creating custom board but some how my board cannot run blinky example...
With a npm1300 I'm able to charge (for instance, the LED showing charging status is on, BCHGCHARGESTATUS is reporting the different steps..... ) but the battery current reporting...
Hello
When following the guidline of a new way to extend boards , VSCode "Add Build Configuration" is blank. Am I doing something wrong or this is not yet supported by...
Hello,
Our company makes module using nRF52840. And we also make development kit with it.
I recently programmed open bootloader built-in hex in nRF5 SDK v17.1.0 (examples...
nrfConnectSDK V2.8
Toolchain
Board: nrf5340dk
Hi, while compiling ncs-spi-master-slave-example , I am getting below errors
In function 'spi_init': C:/Users/hello...
I am currently working on a Direction Finding project, but I am facing an issue in prj.conf .
I use an nRF52811 custom board for Direction Finding. In the board selection...
Hi,
EDITED: This appears to NOT be related to any open circuit, the SAME behavior comes even with abrupt changes to the current scale, without any interruptions. Additional...
Hi, I'm trying to install modem fw using the script given by Sigurd : https://devzone.nordicsemi.com/f/nordic-q-a/53208/updating-nrf9160-modem-firmware-through-the-command...
Hi.
code base is sdk 17.1.0
MCU : nrf52810
Softdevice : S112 (7.2.0)
use SES 5.42a
step1. modify NRF_SDH_BLE_GATT_MAX_MTU_SIZE form 23 to 50 in sdk_config.h
...
Dear nRF experts. We are a module manufacturer and we have designed an nRF45L15 module. We are doing a series of verifications. When we were doing the connection test, we...
