Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi,
in the PCB circuit I marked in the pictures, it seems that vias have been added to the marked areas on the pads of the nRF52840. However, PCB manufacturers say that...
Hi, I am relatively new to the Nordic platform and Zephyr RTOS. I am using nRF Connect SDK version 2.6.0 (the VS Code extension on Windows 11) with the nRF52840DK. I was wondering...
Hi,
I am designing a two Layer PCB with nRF52840 with PMIC, RTC, Flash. Can anyone from Nordic Review it? especially the RF antenna, I have used the Reference design from...
To verify my Custom antenna design on a PCB . AND VERIFY THE PCB.
https://cart.jlcpcb.com/quote/gerberviewThree/?qs=582f0d800a0c49398584815906f24877_1_0_1_0_0.html&_gl=1...
Hi
We are developing Zephyr projects which are compiling and working fine with Visual Studio Code running on a Windows PC.
Now we want to build the projects on a build...
Hello,
I am wondering where the best place to add a transport layer for DFU is? I have both bootloader examples working, but now i need to add the transport layers. On one...
I am implementing SPI communication between the intanRHD2132 (ADC) and nRF52840.
I need to periodically send commands (READ, WRITE, etc.) to the intanRHD2132 (ADC). To achieve...
Hello,
I am using the nRF52840 as modbus client and experiencing some missing bytes during communication (RTU mode) when using a high baud rate (460800). This tends to happen...
Hello, I have a question about how to get commands generated from a client cluster in a coordinator. I am currently developing a hub to control and retrieve data from home...
Hi
I tried to play an audio convert file by NRF52840 via I2S, but the sound output was like noise (incorrect):
This is my config I2S:
The audio file I am using "Audacity...
Hi,
Before, posting I tried this post below, but it did not work for me. It did not print the manufacturing data.
https://devzone.nordicsemi.com/f/nordic-q-a/84753/scan...
I'm using a custom board based upon the nRF52840. The BME680 chip works fine in another RTOS but the zephyr/nRF connect example is throwing errors.
I added a fair amount...
hi
We are conducting SIG certification testing with nRF52832 and DFM.
(CMW270)
The TX test was completed normally.
However, a problem occurred in the RX test.
...
Good morning,
Today for a Brazilian Logistic company, I am developing a Embedded System for Low-power tracking and other features, with a nRF52840 in a RAKWireless solution...
i have developed the VL53L5CX code with BLE nrf52840 and it is working fine but issue i have faced is the USB port Restarted Whenever Firmware Download Process Start below...
