Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
I am trying to work with my flash deivce in my code. for some reason:
const static struct device * int_flash_dev = DEVICE_DT_GET ( DT_CHOSEN (zephyr_flash)); doesnt work...
I have been having a series of issues with programming from nRF Connect using a J-Link programmer. I have made a couple of other recent posts and in each of those, I thought...
hi,all
I used to use nrf54l15dk board as a client server, want to connect to a bluetooth remote,and get bluetooth remote notify message;
I use sample "central_hids...
Hi guys,
I have MQTT v5 up and running but I am currently trying to implement one-way TLS then mutual TLS once it's completed. I am not too sure what I am doing wrong but...
Hi:
My environment is: Windows laptop, nRF52 DK (Peripheral), nRF52840 Dongle, Mobile Central (iOS and Android), and Wireshark nRF Sniffer for Bluetooth.
Peripheral sends...
Hello all,
I have problem with flashing the code. It gives me memory protection error.
Steps I followed for creating firmware and flashing:
1- I took a sample from nrf...
I'm working on a product prototype using the nrf5340 audio dk to send audio via Auracast. We started from the nrf5340_audio application, as it implements a large fraction...
While testing UART communication between a Seeed XIAO board and the nRF9151 DK, I connected the following pins: - XIAO 3.3 V → DK VDD - XIAO GND → DK GND - XIAO TX → DK RX...
Hello,
In the nRF52840 datasheet, some pins are explicitly marked as “low frequency I/O only.” However, I couldn’t find any similar indication in the nRF54L10 datasheet...
Hi everyone,
I’m testing a custom nRF54L15 board with BLE, but it gets stuck inside bt_enable() . To debug the issue, I checked whether my 32 MHz external crystal (HFXO...
Hi, I want to use the external flash on nRF9151-DK (gd25wb256). Having set all the necessary files (prj.conf, nrf9151dk_nrf9151_ns.overlay) and some parameters in the main...
Hi Nordic Community,
I'm testing NFC functionality on the nRF52840 DK development kit using the record_text sample from nRF Connect SDK v2.9.1 (which includes Zephyr OS...
Recently, when using the ncs v2.9.0 SDK, I found that the definitions for some interfaces could not be found. For instance, nrf_radio_packet_conf_t (it cannot be found even...
I am currently working with the Channel Sounding sample on the nRF54L15 DK boards and using Nordic’s multiple-antenna support as described here: docs.nordicsemi.com/.../channel_sounding...
Hi, I’m working on an nRF52840DK-based Bluetooth Mesh project derived from the Chat sample on nRF connect SDK extension for VS Code.
The setup involves three types of nodes...
