Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
I am an FAE with Ezurio, we have a customer who was running through the nRF Connect SDK Intermediate training on DevAcademy and they ran into issues with AuTerm in Lesson...
## Description
On the nRF54L15DK, the measured floor current increases significantly when the GPIO is configured for button edge detection.
### Observed Behavior
* Floor...
Hi,
I am quite new to nrf's and zephyr and I'm working on a product that requires Direct Test Mode functionality. I started with the DTM sample and am now looking at how...
Why do I often fail to compile the examples due to west? The prompt suggests that I need to upgrade west, but I am unable to do so?When directly upgrading West through VSCode...
The solution for "nRF Connect SDK Intermediate - Lesson 9 Exercise 5" does not appear to boot-up after flashing and gives the following output on the com port:
*** Booting...
Currently with the DECT NR+ modem API on nRF91x1 I can schedule rx operations in mode NRF_MODEM_DECT_PHY_RX_MODE_CONTINUOUS given to nrf_modem_dect_phy_rx via nrf_modem_dect_phy_rx_params...
Is there a way to create custom battery profiles of non rechargeable batteries for the nPM 2100 PMIC? Is the nPM Fuel Gauge board compatible with the nPM 2100 EK?
Hello,
I am using nRF5340 with nrf v2.7.99-cs2.
We have interfaced External flash MX25R over nRF5340's QSPI channel. We are using XiP as well and some part of code lies...
I'm developing a Bluetooth mesh lighting controller on a custom board using nRF Connect SDK v2.6.1. I'm trying to add a Sensor Server model to report energy usage, but I'm...
Environment : nRF52833, NCS v3.1.1
Hi. I evaluate PAwR project in my Solution.
PAwR is Fine. But get/set Tx Power is issue.
before add PAwR, My solution used common...
Hello,
I am developing a custom IoT device based on the nRF9151 SiP with a Qorvo QM13345 SP4T antenna switch controlled via RFFE 2.1 interface. All RFFE AT commands fail...
Hi,
I am working on nrf52832 and using SDK 16.
I try to debug the ble_app_buttonless_dfu example, which give error on line 853 in main.c. err_code = ble_dfu_buttonless_async_svci_init...
We are in the process of developing a product using the Thingy91:X as reference.
We need to modify the hello-nrfcloud firmware to suit our application.
Could you suggest...
I am currently working with the Matter sample project and have encountered a question regarding the diagnostic log function. I would like to inquire about how to enable the...
I'm using nrf52840, v3.0.2, scanning BIG/BIS and printing out the BASE.
I first scan the extended broadcast with the label broadcast_id, and then establish synchronization...
