When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I'm having difficulty getting a clean MCK when configuring passthrough (bypass) mode. I'm using ACLK as the source and I do get a 12.288MHz signal on the MCK pin but...
Hi all
In development with nRF91 and my application need to using an external flash memory to store the firmware and I try to follow the example this link below.
https...
Hi, I'm developing an application using internal flash memory. I based on flash_fds example to implement this feature. Now I can write and read data from flash. My basic feature...
Hi,
I have a board using an off the shelf nrf52811 module (from raytac). The only things on the board are the recommended 32k crystal with 2x 12pF caps, as well as two...
Hello,
I've been trying to get my call to app_uart_put() to actually place bytes on the TX pin. Interestingly enough, my call to app_uart_get() works fine and is able...
Am currently trying to implement a client UDP socket application with Mbed DTLS using a Pre Shared Key.
PSK and PSK_ID array values are defined as:
static const unsigned...
Hi,
I am using Thingy 91 in Australia, and I have linked Asset Tracker v2 with overlay-lwm2m.conf to communicate with my own LwM2M server, which is running an instance of...
I'm working towards getting an app derived from MQTT Simple to talk to AWS where I both need to validate the hostname via TLS, and also use public/private certificates to...
Several have asked about this basic situation but I have found no definitive answer.
I erased a dongle with a Segger J-link, and compiled the zephyr samples using CONFIG_BOARD_HAS_NRF5_BOOTLOADER...
My set up is nRF52832 with a board very much like the PCA10040. The SDK is version 16.0.0. I am using Segger Embedded Studio version 5.60 and I am using the GCC compiler suite...
My goal is to have my boot loader write a constant value to RAM and have my applicaton read that same location and retrieve that value.
I am using the stock boot loader...
Hello,
I'm creating a BLE project with a couple of custom services. One of my simple characteristics in a service is a string. When is_value_user = false everything works...
Hey! I am starting my studies in the BLE protocol and I would like to send the ZE03 sensor data through the Nordic UART Service (NUS).
The sensor has 9 bits: 8 data bits...
Hi, I have made a 9160 board, below is the schematic diagram ：
I donwload this example in it, " ncs\v1.9.1\nrf\applications\serial_lte_modem", and send AT command to test...
