When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I'm using GPIO pin as input button with nrf9160 using Zephyr RTOS, but when I was press the button I didn't get any response from button state.
hear is my code
...
My query is:
1. Is it possible to access the azure using WIFI network in above application?
2. After knowing the IMEI using AT Command, in response to which event should...
I am getting more current consumption when internal pull up resistors of nRF52832 are disabled and external pull up resistors of the slave sensor are enabled as compared with...
Hi,
Currently, I am building an application with Bluetooth mesh and I tried to use Zephyr's logging v2 modules. However, when I build it I get MPU-fault errors at boot....
Hi,
I saw in ozone that SW crashed with hard fault explained as escalation of exception that was not enabled.
How can I enable all exceptions to see the exact reason of...
Hello, I'm using nrf52833, pca10100.
My project is based on 'ble_app_uart', and I added buttonless DFU project.
this is ble_dfu_buttonless_async_svci_init() function...
I have succeeded in running the Multi-NUS package on the nRF52840DK. My client's client learned of the nRF21540EK and wants to try using it to extend the range in the present...
i cannot seem to select nRF Connect SDK when creating application in vs code. i already install the nRF Connect SDK v2.0.0 from the toolchain and the nRF Connect Toolchain...
I am trying to build a example program in KEIL for the nRF52832 QFAA device. When I sart KEIL the program shows a massage that says the nRF_DeviceFamilyPack.8.3.1 is required...
Good day to all I am trying to change the Application on a device with an nRF52832 chip with an existing firmware. To do this, I use nRF Connect for Mobile 4.25.3. From the...
I am developing GATT Server Reader Firmware usng nRF SDK COnnect using NRF52840
I have implemented two services in reader FW in two files say: service_a.c and service_b...
I have tried installing the nrf connect 3.11.1 on 2 different windows 10 machines. Both are clean windows 10 installs. The hard drives were wiped and windows reinstalled....
Hi,
the following event is generated when I connect two or more nRF9160DKs to a Windows machine: "Disk 2 has the same disk identifiers as one or more disks connected to...
1. 2. 3.
I am using the ble_app_beacon example as the starting point for my project. I am working on a project where a number of beacons will advertise its identity and...
How do you enable any of the i2c peripherals on the nRF9160 dk boards?
I tried changing the device overlay to the code below:
& i2c0 {
status = "okay" ;
compatible...
