When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I am working with nRF52832_dvk board, i am testing the OTA example as per in this link. https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts...
Hello, I'm starting to design the pcb for the nrf52840. I looked but I saw that it is also possible to create it on two layers instead of four as the reference design teaches...
Hi,
I am trying to burst read FIFO of ADXL362 with zephyr adxl362 sample. 1 byte tx (read fifo command) and n byte rx ( reading the fifo data);
Zephyr is the last version...
Hi,
We tried to use Connect Interval 7.5ms with MTU 88B, both central and peripheral role are 52832, but observed disconnection after 30 sec.
Disconnection reason is 0x13...
Hello all,
Background: -NRF5340 -NRF SDK 1.9 -Zephyr 2.7.99
My objective is to send a data of 768 bytes by BLE. I use 4 notify to send this 768 bytes data (192 packets...
Hello,
I'm working on an application running on the nRF9160. The application is build on the Fanstel BLG840X and the code is shared between both the 52840 and 9160 on the...
Hello!
I have a problem updating network core firmware through MCUboot when NSIB is enabled (through "CONFIG_SECURE_BOOT=y" in my application prj.conf).
Without NSIB...
Hello Support, I'm looking for reference schematic for the interface between nrf52840 (or similar) and the nrf21540 . Is there a simpler version than the developer kit user...
Hello again,
I'm trying to lower the power consumption of my thingy91 by turning off the serial by setting config_serial=n. Unfortunately, this causes a crash while running...
Hi I would like to start developing wireless and embedded solutions using Nordic Ecosystem SoCs. I will probably only need to use BLE 5.0 and maybe Bluetooth Mesh so nRF5...
Hi,
So we have a project where we use the NUS, and we need to detect when a client subscribes. We eventually found a way, but it seems very obtuse and a bit black magic...
Hello,
I'm working on a BLE application using zephyr and nRF Connect SDK 1.8.0 on the nrf52840. I'm debugging the BLE stack using ozone but whenever I set breakpoints the...
My Current nRF Connect SDK version: 1.5.0
I am trying to follow this reference https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.5.0/nrf/samples/nrf5340/netboot/README...
