When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi!
Continue the previous case
I try to run zephyr direction finding rx example direction_finding_connectionless_rx
It seems to me that the external antenna is working...
Hi
I am working as a member of a team owning nrf9160 dk. I want to work remotely with the same hardware they have. but right now I do not have physical access to the hardware...
Hi, I installed VS. The screen shot is shown below. How to open, Build, Compile, RUN and Debug sample applications and custom existing SES projects. May, some one explain...
I am trying to program my nRF51 QFAC, but it tells me to adjust my linker settings.
I am using the SDK 12.3 and the softdevice 130 2.0.1.
However, after I apply the...
MCU : nrf52833
SDK : Ver 17.1.0
SoftDevice : S140
I try to call RTC value to external RTC Module by TWIM in BLE authentication rw request event.
But MCU stop to...
Good afternoon,
I built and flashed the Bluetooth Multiple advertising sets sample in VS Code using the nRF Connect Extension Pack onto my nRF5340-DK and come across an...
I am trying to measure my battery level on my nRF51822 beacon board through the internal ADC.
The chip is just advertising itself every 5 seconds.
The measurement works...
Hello,
I am trying to develop a low-power application based on the direct test mode example. I saw in this blogpost: https://devzone.nordicsemi.com/nordic/nordic-blog...
Hi there,
We are currently developing and testing on the nRF5340. We are using our own OS (not Zephyr).
We measure power on the devkit by connecting the PPK2 as a source...
Good day I am wondering if anyone can help me
For background information.
Network - NB-iot
Firmware - 1.3.1
Software - Serial LTE Modem
Hardware - nrf9160dk
...
Hi,
i wanted to i2c interface of nrf with adc ic 3427. i am trying to interface by refer example of twi_scanner device address get found correctly.
now i am trying to...
On an nRF52840 using SDK 15.3 and FreeRTOS 10
I've got both a PCA10056 dev kit and a custom board. I don't think I've got a hardware issue here but I'm running the usb_msc_pca10056...
Hi guys,
I have developed a custom board using the nRF52840 module and the SDK16.If the peripheral is disconnected from the central, it starts advertising again in normal...
I have a custom nRF52480 board and addded mesh functionality based on the light mesh sample
The app crashes during provisioning from the nRF Mesh app.
Relevant portion...
Hello,
I would like to enter simple commands such as on, off to the USB CDC ACM, and then set the parameters in the model through string comparing.
(now i'm trying Generic...
