Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi everyone,
I have setup a Bluetooth Mesh network of 5 Light Control Server Nodes and 5 Low Power Nodes that have friendship with eachother.
All nodes publish and subscribe...
I'm facing the requirement to save few kb of data in flash and process it over time. Because none of the standard mesh models fit, a custom mesh model will be the only option...
Hey,
I encountered a very strange problem while I was trying to connect from nRF52832 (as a central device) to my nRF52805 as a peripheral. If I am trying to connect to...
Hello,
I am working on a custom development board that is using the nRF52840. After programming the nRF52840 on the board with Soft Device s140_nrf52_7.0.1_softdevice.hex...
Hello DevZone,
A product I use uses NFC tag type 2 to communicate. It usually communicates to a separate chip but I want to replace this with the nRF52832.
I opened...
Hello,
I'm working on a product where we want the nRF52840 to be able to reset itself in hardware . This is currently done via an IO that drives a SHUTDOWN# signal into...
Hi,
I'm using TWI to control accemeter(MMA452).When I used TWI SENSOR to read my sensor, it didn't work normally.
The address of MMA8452 is 0x1C,so i want to read...
The separation of flash memory into a region for the application core and one for the network core on the nRF5340 seems rather cumbersome and error-prone.
I'm especially...
Hi,
will qmi_wwan or gobinet driver be available for nRF9160? PPPD is not available. It is quite a limitation in use to miss ethenet interface based connectivity.
Regards...
Hi everyone, I’m have a wired network of 1000 devices (relay switches) that I’ve been tasked to upgrade to wireless.
Devices are inside a warehouse, about a pallet apart...
Hello All,
I am developing product using nRF52840 Dev-kit and SDK 4.1 for zigbee and thread.
I have created the new solution using tool chain - C:\Program Files (x86)...
Hello,
I'm using the NRF52840 with the NRF5 SDK v15.3.0 and S140.
I was trying to include the nrf_fstorage library into an existing project. The problem I experienced...
Hello,
I modified a sample app "blinky" on segger, to include main.cpp instead of main.c Then when I built, I got a compile time error stating in main.cpp "void main(void...
Hello.
I'm looking at options for a BLE device that has fairly small application requirements. It would essentially be a button, so the peripheral blinky example would make...
Hi Nordic!
We are gonna do pre-compliance testing of our custom board, with mounted nRF52840 and nRF9160 SICA B0.
We are looking for any software available from Nordic...
