Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
In 2.7.0 in file c_cpp_properties.json I had direct path to compiler. Now moving I need to change the path.
AI suggested to use ${nrf-connect.toolchain} for compiler and...
I want to use the UART to receive data, but that doesn't look possible if I use the Logging Module. I don't see where the logger module will interrupt my code to tell me I...
I'm currently working on a project using the nRF52832 as my controller, Segger Embedded Studio version 5.42a as my IDE, and the nRF5 SDK 17.0.2. I started by developing a...
Hello,
We are using the Message Routing API of nrfCloud to consume messages via Webhook and DLQ. We have several devices placed in different device groups (e.g. prod_devices...
Somewhat related to this:
I'm wishing to optimise code (removing a load of volatiles) by ensuring most of my application code runs at the same interrupt as the NRF_SDH_BLE_OBSERVER...
Hi,
I have 2 problems in power profiler kit II:
Problem 1: When I connect the porfiler kit II to the computer, the computer can't identify the PPK2
Porblem 2: The output...
I want to know how to adjust the TX RX setting for the nRF52833 DK connected to the nRF21540 EK shield. I have already added -DSHIELD="nrf21540ek" to the build configuration...
Hello.
I am trying to repeat the functionality of the project that is shown in this video https://www.youtube.com/watch?v=fCU8x-pmtqU&list=PLx_tBuQ_KSqG-leiJDfOKf_ZmCqHnbi4r&index...
We are using SDK v2.6.1 for our application, along with the Fanstel module WT02C40C.
Internet connectivity is provided to the WT02C40C module via a hotspot, with CONFIG_STA_KEY_MGMT_WPA2...
The "nRF Command Line Tools" page, https://www.nordicsemi.com/Products/Development-tools/nrf-command-line-tools says " Important: The nRF Command Line Tools is in the process...
I want to interface 3 custom made heater boards to nrf5340dk. Where the simple task is to toggle gpio's to Turn ON & OFF the heater board. Now, we are using P 0.01, 0.02 &...
Hello, I am considering the prospect of using channel sounding as opposed to UWB for indoor asset tracking. I can understand, that the main limitation with that would be,...
Hi There:
I used the nRF7002 DK to evaluate its WiFi throughput performance.
The test environment is below:
1. nRF7002 DK
2. NCS version: 2.5.0
3. Sample application...
Hello Everyone,
I have configured SPI1 at 1MHz, to receive data with a sensor. Basically i am reading data from a sensor device. So calling spi_transceive_dt() with 4...
