I am working on an application and need to get the exact time that the master node receive advertising from the slave node. I tried with PPI and it's ok to capture the Radio...
Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hello all. Is there a possibility to implement a "software watchdog" on the nRF51822 SoC. I would like to react with this watchdog not on external events (e.g. hardware-actions...
Program received signal SIGTRAP, Trace/breakpoint trap. HardFault_Handler () at ../../../../HAL/NRF52/HAL.cpp:122 122 __debugbreak(); (gdb) bt #0 HardFault_Handler () at ...
Hi,
I've added usb function to nRF52840 project accroding to usb sample projects.
The function was all right but the device manager showed the the 52840 as "USB serial...
Using windows 10 OS, and SES v5.40.
I am using nRF52833 device in my project along with nRF5_SDK_for_Thread_and Zigbee_v4.1.0_32ce5f8 SDK.
The timer is called for every...
I have a Fanstel BT832X evaluation board (model EV-BT840(832)-V4). Nordic examples without softdevice are working fine. Examples with softdevice are not working. I have checked...
I’m getting some strange behavior after repurposing the WS2812 driver sample with the following code. Note that my code has Bluetooth enabled. It seems like it might be some...
I use ncs1.6.0 to develop on nRF52832DK. The current requirement is to enable PA LNA support on mesh.
I learned how to use FEM driver through this blog . I added the corresponding...
Hello,
Is it okay to supply the nRF21540 with a DC/DC or do I need to use an LDO? Are there any performance differences of the nRF21540 when choosing one over the other...
I'm finding that the signal strength of the radio is too low in my nRF52840 custom BLE project. I would like to increase the radio power from the default 0dB as our RSSI values...
I made a custom model under ncs1.6.0 to publish uart data. When the data I want to publish exceeds 85 bytes, an error occurs in debug:
<err> bt_conn: Unable to allocate...
NCS v1.6.0
CONFIG_SLM_GPIO_WAKEUP =y
CONFIG_SLM_INTERFACE_PIN =24
When Serial LTE modem is woken up after #XSLEEP=2 without 2s delay, it starts to loose some unsolicited...
Hello,
I'm using the sdk v17.0.2 with softdevice s140 with a custom PCB shipping the nrf52840.
I'm facing an issue where I cannot enable NFC and softdevice at the same...
Hello everybody. I am currently evaluating some BLE Tags, if they can be used as an BLE doorkey. The chips I am talking about are the following: nRF51802 nRF51822 nRF52832...
