When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello,
I'm working on a project related to DWM1001-DEV at University of Illinois at Urbana-Champaign to build a demo of the product that uses UWB. However, I'm having several...
Good day
Please assist, I had my power profiler (PPK II)and Bluetooth dongle both plugged into my laptop. I accidentally upgraded the firmware for power profiler (PPK II...
Hi
I am using NRF5340dk with NCS version 1.5.0, I need to port the below library which was written for nrf51.
github.com/.../ADS1231
KIndly, Help me to resolve this...
I am using SDK nRF5_SDK_15.3.0_59ac345 with nrf32832. I want to write data from central to peripheral characteristics. I wrote below code:
Everything worked fine when...
I run the program step by step, when execute NRFX_IRQ_ENABLE(SAADC_IRQn);, it will go to app_error_fault_handler,.What's wrong ? I have do nothing with it!
I am trying to set a timer pulse at 500kHz and on every high pulse i want to do a read on another pin.
I have an IC HX711, that has a 24bit output MSB. every positive...
Hi,
im a beginner and i have problems to integrate the Homekit SDK in the Connect SDK.
Maybe anyone have a link to a tutorial?
The implementation by west has no effect...
Hi, Q1) I am facing an issue with the heap memory. I am using the Cjson_Parse function which uses quit a lot of memory. So I am wondering if there is a way to increase the...
Hello,
i m working on usbd example on nRF52
i have a problem that usbd stops sending data aftew few time. the port is still enabled but the data is not sent! any proposition...
I am trying to communicate with a sensor that has some interesting timing requirements for reading information from it, it requires ~100us delays between the address to read...
I want to calculate the power consumption used by many peripheral like GPIO, TWI, UART, SPI, RTC, SAADC. I can't find these information in nrf52840 PS v1.1
Because I don...
Hi, On my Windows 10 machine I've installed nRF Connect for Desktop (v3.7.0) and then used Toolchain Manager utility for installing nRF Connect SDK (v1.6.1). Afterward, navigating...
Hi,
I'm working on a project using BLE via s140, everything was working fine until I wanted to implement usb.
I created a blank project in order to validate the usbd then...
Hello, I have and audio source and i would need to divide it beetween two frequencies (<95Hz and >=95Hz).
Im trying this thing with a nRF52840 and i was looking at DSP libraries...
hi support team,
i have one question about DFU function question,:
in our ncs sdk , nrf5 desktop can dfu from hid feature(from configuration channel setting ), if it...
