I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I encountered the error MPSL ASSERT: 1, 1310 when establishing a BLE connection on my custom board, only happens when using an external 32 kHZ crystal oscillator (
CONFIG_CLOCK_CONTROL_NRF_K32SRC_XTAL...
Hello everybody,
I have very bad problem for me. I am developing application on nrf7002-DK based on STA (station) example. I add own AT command analyzer and SCAN, so I...
Hello
Im trying to send data[3000] using USB, problem is I need to finish transfer within 13ms because after that period new data is ready to be sent. In this Interrupt...
Hi,
We have been working on our nRF5340 custom board with ncs V2.0.2.
Our application runs for 10 minutes to collect some sensor data and transfer it over BLE, then it...
Hello,
I am trying to do the current measurement for the 2NR EVK in sleep mode.
I am using the "Bluetooth: Peripheral power profiling" application that I was able to build...
I'm trying use nrf52810 as the peripheral to connect my nrf52840 central.
The hardware buyed from other vendor in local market, it looks very simple, maybe based on nrf52810...
When the Thingy 91X is connected to a laptop via USB C, there is a drive available that contains a few files - config.txt, readme.txt, and an inf file.
Is it possible to...
I want to know the configuration of Nordic's GPIO pins. I only want to use one callback function, but due to the many buttons on my mouse device, it is not possible to configure...
When I was studying Zephyr, I found that some of the enumerations used by Nordic couldn't be found in Zephyr, so I was wondering if Noridc had encapsulated them in Zephyr...
Hello, as from title, after updating from ncs 2.7.0 to 3.0.2 my application cannot advertise and scan concurrently anymore.
If I start advertising after starting a scan...
Hello,
I would build the Matter nRF Connect Lighting Example Application from the SDK for the nRF54L15-DK. Coud you add support for it in the Matter SDK?
Regards
I am developing a custom USB module based on the nRF54L15 chip. I would like to know how I can initially flash firmware onto the board.
My plan is to have a custom bootloader...
Hi,
I'm working with a custom PCB, with nPM1300 and a microcontroller.
The problem is that working only with battery the nPM1300 VBUS pin show 2.4V and I cannot put...
