Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hello,
I use nrf52832 with 65 kb RAM.
I can't understand why soft device takes about 30k RAM memory.
I see "reserved_ram" has 30k.
Can I change size for 20k for...
We're using the nRF52840 on a battery-powered device that requires very low power consumption, both in run mode and also in the Cortex-M4 sleep / deep sleep modes. We've recently...
Hi, I'm trying to enable the entropy driver so that sys_csrand_get() will stop returning "Entropy reseed error". Does anyone know why it's grayed out? I have tried enabling...
Hi,
I know it's a very common question, but I still haven't fully understood. There is nrf52832 on the peripheral side, there is ble dongle on the central side.
How does...
Hi,
I am trying to get a project to compile using the the segger studio. I have copied one of the example applications and converted it according to your instruction here...
Hello,
I want to add a new driver directly in my project (out of tree), so I've add the differents files, as in the picture below.
When I compile, I get each time...
HI
I used NRF24L01 module in direct mode and chose 250kbps in configuration
In TX mode : whether the data from MCU to module has to be send through exact 250kbps?
Dear Sir
I am trying to work with the ADC .
Attached a code
I get the lines
00> Adc sample 13772 00> Adc sample 13772 00> Adc sample 13772 00> Adc sample 13772...
Hi Nordic Team,
Some time facing Connection issue in Mobile app and some time device advertisement is not getting in app.
I am using below chipset and configuration. ...
Dear all, I try to self provision device by it self following steps below: Step 1 : Bind key Step 2 : Subscribe to topic
Step3 : Set publication topic
Step 4 The main...
I am having issues running GPS and LTE concurrently on the nRF9160DK and am wondering if the rootcause is an incompatibility between modem FW v1.2 and hardware v0.9.0. I am...
Hello,
With regards to the HID Keyboard Example,
1) Is it posible to disconnect from the central side (ios)? I would like to be able to disconnect as follows:
But...
Hi,
I have just started using the Nordic SDK (nRF5_SDK_15.2.0_9412b96) and am developing a low power application for a custom PCB using the rf52840.
I am developing...
I can read the spi flash id by the other mcu with the above code, but can not read correctly by
nrf52832, is there something wrong with my handle?
SPI FLASH ID 0E 40 13...
